Integra DTR-6.4/5.4 - Manual (Page 47)

47
Listening Modes
-- / ---
1 2 3
4 5 6
+10 0
7 8 9
Audio Sel Muting
Angle Subtitle
TV / VCR
Random Audio Adjust
Enter
Search
Input Selector
Dimmer Zone 2 Display
VOL C H
Disc
Rec
Level
SURR
Stereo Direct
All ST
Pure A
THX
A M
V 1
DVD
V 3 V 4 V 5
C D
V 2
P H
TAP TUN
RC-517M
SP A SP B CINE FLTR CINE FLTR
RCVR
Mode
Listening mode buttons
Listening mode
buttons
DTR-5.4
• Refer to pages 44 and 45 for more details of listening modes.
• Refer to page 45 for sources and listening modes.
• When playing Dolby Digital or DTS software, the listening
mode will automatically change to Dolby Digital or DTS.
Tip:
You can set in advance a different listening mode for each input
source. For more details, see page 57.
When using the remote controller, first press the RCVR
Mode button before preceding to the step below.
Press one of the listening mode buttons to select the listening mode.
Direct: Changes the listening mode for the signal type that is
currently being input from the selected input source to the Direct
listening mode. If pressed, the corresponding settings in the “Input
Setup” menu for the selected input source is also changed (see page
57).
Stereo: Changes the listening mode for the signal type that is
currently being input from the selected input source to the Stereo
listening mode. If pressed, the corresponding settings in the “Input
Setup” menu for the selected input source is also changed (see page
57).
Surround (SURR): Changes the listening mode for the signal type
that is currently being input from the selected input source to the
surround mode that matches the signal type (e.g., Dolby Pro Logic
II, Dolby Digital, DTS, or DTS Neo:6). If pressed, the
corresponding settings in the “Input Setup” menu for the selected
input source is also changed (see page 57).
All ST (remote controller only): Changes the listening mode for
the signal type that is currently being input from the selected input
source to the All Ch Stereo listening mode. If pressed, the
corresponding settings in the “Input Setup” menu for the selected
input source is also changed (see page 57).
Selecting a listening mode (DTR-5.4)
1 2 3
4 5 6
9
SURR All ST
Stereo Direct
DSP
Pure A
CINE FLTR
DTR-5.4
Remote controller
DSP: Changes the listening mode for the signal type that is
currently being input from the selected input source as shown
below.
Orchestra
→ Unplugged → Studio-Mix → TV Logic → All Ch
Stereo
→ Mono → T-D → Mono Movie → Enhance → Orchestra.
If pressed, the corresponding settings in the “Input Setup” menu for
the selected input source is also changed (see page 57).
The CinemaFILTER function gently decreases the level of the
extreme high frequencies, compensating for overly-bright sounding
motion picture soundtracks. Select this function if the sound from
the front speakers is too bright.
This function only works in the Dolby Digital, Dolby Digital EX,
Dolby Pro Logic II Movie, DTS, DTS-ES Discrete 6.1, DTS-ES
Matrix 6.1, DTS Neo:6 Cinema, All Ch Stereo, Mono listening
modes.
Press the CINE FLTR button on the remote controller.
The current setting is displayed. Press the button again to change
the setting.
On: The CinemaFILTER function is used during playback.
Off: The CinemaFILTER function is not used during playback.
Note:
Dolby Pro Logic II Movie, DTS Neo:6 Cinema, Dolby Digital, and
DTS are only enabled for multichannel playback.
Original filter (CinemaFILTER) loading for movies
(DTR-5.4 only)