JVC SR-V10U - Manual (Page 7)

EN
7
1
Check contents
Make sure the package contains all of the
accessories listed in “SPECIFICATIONS”
(
੬␣ pg.␣ 63).
2 Situate VCR
Place the VCR on a stable, horizontal surface.
3
Connect VCR to TV
The following connections are required.
RF Connection
1 Disconnect the TV antenna from the TV.
2 Connect the TV antenna cable to the
ANTENNA IN terminal on the rear of the VCR.
3 Connect the supplied RF cable between the TV
OUT terminal on the rear of the VCR and the
TV’s antenna input terminal.
AV Connection (improves picture quality during
tape playback.)
If your TV is equipped with audio/video input
connectors
1 Connect the antenna, VCR and TV as shown in
the illustration.
2 Connect an audio/video cable between the
AUDIO/VIDEO OUT connectors on the rear of
the VCR and the audio/video input connectors
on the TV.
S-video Connection (allows you to make the
most of the S-VHS picture performance.)
If your TV is equipped with an S-video input
connector
1 Perform “RF Connection” and RED/WHITE
AUDIO connections.
2 Connect an S-video cable between the S VIDEO
OUT connector on the rear of the VCR and the
S-video input connector on the TV.
4
Connect VCR to power source
Connect the AC power plug to an AC outlet.
● The clock and tuner channels will
automatically be set when the antenna is
connected and when the AC power cord is first
connected to an AC power outlet (
੬ pg. 8).
(If “Auto” or “CH” is displayed on the front display
panel before the VCR is turned on, the clock and
tuner channels are being set automatically. Wait
until the clock time is displayed on the front display
panel before turning on the VCR.)
5 Set VCR channel
Press POWER to turn off the VCR and press STOP/
EJECT (
§ ) on the front panel for more than
5␣ seconds. “3CH” appears on the display panel.
Press CH + and – on the Remote to select “3CH” or
“4CH” for only RF connection, “–CH” (OFF) for RF
and AV connection, then press OK.
● The VCR channel is preset to 3CH.
Set to 4CH if 3CH is used for broadcasting in your
area. (To view the picture from this VCR through
this channel, select the same channel on the TV
with the VCR channel setting on the VCR.)
● You can now perform basic playback
( ੬␣ pg.␣ 15) or basic recording (੬␣ pg.␣ 19).
NOTES:
● The VCR channel is the channel on which you can watch the
picture from the VCR on the TV when only using the RF
connection.
● Even if you are using audio/video cables to connect your VCR
to your TV, you must also connect it using the RF cable. This
will ensure that you can record one show while watching
another (
੬ pg. 21).
● For full identification of the VCR’s rear panel, refer to the
Index (
੬ pg. 61).
IN REMOTE
IN OUT
R
L AUDIO
VIDEO
VHF/UHF
ANTENNA IN
TV OUT
REMOTE
OUT
IN OUT S
V I D E O
A
Installing/Removing the lithium battery
1 Make sure that the power plug is connected to an AC outlet
and turn off the VCR power.
2 Open the battery cover while pressing the release tab as
illustrated.
3 Insert a lithium battery with the plus (+) side up and push it in.
●
To remove the lithium battery, press the latch A down-
ward using a pointed non-metallic object, then pull out
the lithium battery.
4 Close the battery cover until it clicks in place.
Be sure to connect the power plug to an AC outlet first
before installing the lithium battery; otherwise, the
battery's service life will be drastically shortened.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○