Sony XDCAM PDW-1500 - Manual (Page 48)

Chapt
er
4
Re
c
o
rdin
g/
Pla
y
ba
c
k
48
4-2 Playback
4-2 Playback
This section describes playback of video and audio.
Disc playback start position
Although this unit uses optical discs, it is designed to offer
the most convenient features of tape playback by VTRs.
One of these is the playback start position, which works in
the same way as tape, as described below.
After playback stop
The unit stops at the position where the STOP button was
pressed.
Press the PLAY button to resume playback at the stop
position.
After recording
The unit stops at the position where recording ended.
To play back a clip, press the PREV button to move to the
start frame of any clip, or press the PREV button with the
PLAY button held down to move to any position.
After disc insertion
The unit stops at the position of the disc when it was most
recently ejected.
Press the PLAY button to resume playback at the most
recent position.
The playback position is saved to the disc when the disc is
ejected, which allows playback to start at that position
whenever it is loaded into any XDCAM player.
Note
This function is not available when the Write Inhibit tab of
the disc is set to the recording disabled position, and when
extended menu item 310 “REC INHIBIT” is set to “on.”
The REC INH indicator may light when neither of the
above are true if the format of recorded sections on the disc
is not the same as the recording settings of this unit. In this
case, the playback position can be saved to the disc.
4-2-1 Preparations for Playback
Button/switch settings
Before beginning playback, make any necessary button/
switch settings. For details of the settings of the buttons/switches, see the
pages indicated in parenthesis.
REC
VARIABLE
PRESET
PB
L
MIX
R
MONITOR
NETWORK
LOCAL
REMOTE
ACCESS
PHONES
TOP F REV F FWD END
PREV NEXT PLAY
AUDIO MONITOR SEL METER SEL INPUT CH INPUT SEL VIDEO INPUT SEL COUNTER SELECT
SUB
CLIP
THUMB
NAIL SET RESET
SHIFT
EJECT
HOLD SYS MENU MENU
STOP REC
SH UTT LE
JOG VAR
MARK1 ESSENCE MARK CLIP MENU S.SEL
MARK2
IN OUT
ALL/CH-1 CH-2 CH-3 CH-4
OVER dB
-12
-20
-30 -40
-60
0
CH- 15
SG DATA
ANA SDI
AE8/EBU
OVER dB
-12
-20
-30 -40
-60
0
CH- 26
SG DATA
ANA SDI
AE8/EBU
OVER dB
-12
-20
-30 -40
-60
0
CH- 37
SG DATA
ANA SDI
AE8/EBU
OVER dB
-12
-20
-30 -40
-60
0
CH- 48
SG DATA
ANA SDI
HOURS MINUTES SECONDS FRAMES
AE8/EBU VITC VITC COUNTER REC INH VIUB
EDIT KEY INH REMOTE [9P iLINK] INPUT
i.LINK
SDI
1/2 5/6 3/4 7/8 625 525 IMX[50 40 30] DVCAM 4 8 CH 18 24 BIT
CMPST
Y-R,B
SG
ALARM
MONITOR
AUDIO
POWER switch (page 22): I side
(on)
On/standby switch (page
13): Indicator (") lit green.
Audio level adjustment section (page 16):
Adjust the audio playback levels
Remote control switch (page
13): LOCAL
COUNTER SELECT button
(page 13): Select the data
(elapsed playback time, time
code value or user bit data) to
be displayed in the time data
display. When displaying the
time code value, select TC or
VITC with extended menu
item 629 “TC SELECT.” AUDIO MONITOR SEL
button (page 15): Select
the audio channels to
monitor.