Sherbourn Technologies PT-7010A - Manual (Page 33)

33
NOTE: To erase Punch commands from a device (return
buttons to their previous programming): Repeat steps 1
and 2, then press the device button twice. Repeat for other
devices, then press MAIN to return to SETUP.
ERASE
Use this mode to erase commands stored in the remote.
This does not affect the labels, just the stored IR
commands. The pre-programmed commands for the PT-
7010A can be lost. Please follow this section
CAREFULLY!
1) In the SETUP mode, select ERASE and the display
will show LEARN, FAV, MACRO and EXIT.
2) If you select LEARN, press ALL to erase all learned
buttons, or KEY to erase one device at a time. If you use
KEY, press MAIN and EXIT when you have erased all
the devices you want.
NEVER select ALL! This will erase the 7010A
operating codes and the remote will have to be sent to
the factory for reprogramming.
3) If you select FAV, press ALL to erase all favorites, or
KEY to erase single favorites. Note that the labels are not
erased.
4) If you select MACRO, press ALL to erase all macros,
or KEY to erase macros, one device at a time.
5) Press EXIT to return to the SETUP menu, and press
MAIN to return to the main device menu.
LIGHT
This mode allows you to either disable the light, or change
the number of seconds it stays on. (The light is inactive
while in the SETUP mode).
1) In the SETUP menu, select LIGHT and the display
will show ON, time in seconds, SAVE and EXIT.
2) If you press ON, it changes to OFF and disables the
light. This is useful if you want to save battery life, or if
you have children who like to use the remote as a flashlight.
3) Use the keypad to enter the amount of time (in seconds)
in which you wish the light to remain on after releasing
the light button. If you enter 00, it only stays on while the
light button is held down.
4) Select SAVE, or press EXIT to make no change. Either
of these will return you to the SETUP menu.
MACRO
The macro mode allows you to set up certain buttons to
transmit up to 20 commands in sequence. For example, a
single button press could turn on all of your home theater
equipment, and set the PT-7010A to DVD, set the TV to
channel 3, and set the DVD to play, make the tea and put
the cat out.
The buttons which can be programmed as macros are: M1,
M2 and M3 at the bottom of the remote, and Power and
System at the top. The ten device buttons can also be
programmed as macros, although these will only be
activated if the device button is held down for a few
seconds.
Note that the macro buttons are independent of which
device the remote is set for. So there is only one M1 macro,
only one power macro etc.
1) In the SETUP mode, press MACRO.
2) Press one of the buttons you wish to program as a macro,
such as M3, Power, or a device button.
3) Press up to 20 buttons you would like the macro program
to store. Do this in the exact order you want them to be
transmitted. Use the PAGE, FAV and the direct buttons to
find buttons to use in the macro.
4) To add a delay between steps, you can add 0.2 seconds
each time you press PAUSE (II). This does not take up a
step.
5) Press the CHANNEL UP button to save your macro.
6) Repeat this procedure to program more macros, and
press MAIN to return to the main menu.
7) Try out the macros to see if they work as expected. It
may take some time to transmit all the commands in
sequence, so keep the remote pointing at your equipment
and do not move it during this time.
Note that the remote’s ZONE 2, PAGE 2 has discrete on
and off codes for the Main Zone and Zone 2. You can use
these within Macros instead of the main power button
commands (which toggle on/off).
RECAL (Recall)
This mode lets you quickly see the three digit codes you
have assigned to each device. This is useful if you want to
check the tables and find other codes which may work
better.
1) In the SETUP mode, select RECAL. The device labels
and their codes will flash alternately, before returning to
the SETUP menu. Make a note of the codes.
2) Press MAIN to return to the main device menu.
CLONE
This feature allows you to easily copy all of the commands
and labels from one Sherbourn remote (of the same type)
to another.
1) Set both remotes on a flat surface, with their IR windows
pointing towards each other, about 1 or 2 inches apart.
2) In the SETUP menu for both remotes, press CLONE
and the display will change to show SEND, RCV (receive)
and EXIT.
3) Press SEND on the remote you want to copy from. Press
DEVIC to only clone a single device, then press the device
button. Press ALL to clone all programming.
4) Press RCV on the remote you want to copy to.
5) When you are ready, press START on both remotes. It
may take up to 1 minute to complete the clone sequence