Samsung iDCS 100 - Manual (Page 52)

45
light is lit will cause the keyset to return to handset mode and the light will
go out.
HOT KEYPAD
On your phone system your keyset’s keypad can be made “live” or “hot” so
that it is not necessary to lift the handset or press the SPEAKER key before
you begin dialing. Calls can be made and features activated by simply dial-
ing the C.O. line number, trunk group access code, intercom number or fea-
ture access code. To activate this feature:
• With the handset on-hook, press TRANSFER and then dial 110.
• Dial 031 to turn the Hot Keypad on or 030 to turn it off.
• Press TRANSFER to store your selection.
KEY CONFIRMATION TONE
You can hear a short beep (confirmation tone) each time you press a button
on the dial pad. This tone can be turned on or off.
• While on-hook, press TRANSFER and then dial 110.
• Dial 040 to turn tones off or 041 to turn tones on.
• Press TRANSFER to store your selection.
REJOINING A PAGE
This feature allows you to hear the remaining portion of an ongoing internal
page after you return your keyset to idle. To enable this feature:
• With the handset on-hook, press TRANSFER and then dial 110.
• Dial 051 to turn this feature on or 050 to turn it off.
• Press TRANSFER to store your selection.
RING PREFERENCE
This feature automatically answers ringing calls when you lift the handset or
press the ANS/RLS key. This method will always answer calls in the order
they arrived at your keyset. When you turn ring preference off, you must
press the flashing button to answer a call, allowing you to answer calls in the
order you choose.
• With the handset on-hook, press TRANSFER and then dial 110.
• Dial 061 to turn ring preference on or 060 to turn it off.
• Press TRANSFER to store your selection.
SET ANSWER MODE (INTERCOM)
You can receive internal calls in one of three modes (see Answering Intercom
Calls under Intercom Calls for descriptions):
• While on-hook, press TRANSFER and then dial 103.
• Dial 0 for Ringing, 1 for Auto Answer or 2 for Voice Announce.
• Press TRANSFER to store your selection.
NOTE: When your keyset is programmed for Auto Answer and you have For-
ward No Answer (FNA) turned on, you must answer screened transfers by
pressing the ANS/RLS key before your FNA timer expires or the call will for-
ward.
SET ANSWER MODE (CO)
Your incoming CO calls can be set to follow the intercom answer mode.
• While on-hook, press TRANSFER and then dial 110.
• Dial 15 to access AUTO ANS CO.
• Press the VOLUME UP or DOWN key to change status.
• Press TRANSFER to store your selection.
AUTOMATIC HOLD
While on an outside call, pressing a line key, route key or a flashing CALL
button will automatically put your call on hold and connect you to the next
call. This feature can be turned on or off at your keyset.
• With the handset on-hook, press TRANSFER and then dial 110.
• Dial 001 to turn Automatic Hold on or 000 to turn it off.
• Press TRANSFER to store your selection.
NOTE: Intercom calls can be automatically put on hold by pressing TRANS-
FER.
HEADSET OPERATION
Keyset users can switch between headset mode and handset mode. When
using headset mode, press the ANS/RLS key to answer and release calls.
• With the handset on-hook, press TRANSFER and then dial 110.
• Dial 021 to use the headset or 020 to use the handset.
• Press TRANSFER to store your selection.
Your keyset may be equipped with a Headset mode key. If it is so equipped
pressing this key while the light is out will cause the keyset to enter headset
mode and the light will illuminate to indicate this. Pressing the key while the
44
HOME PAGE Table of Contents Guide-Contents