Sony Ericsson PDW-530P - Manual (Page 87)

Cha
p
te
r 6
Men
u
Dis
pla
y
s
and
Det
a
iled Se
tt
ing
s
87
6-2 Status Display on the Viewfinder Screen
6-2-3 Display Modes and Setting
Change Confirmation/
Adjustment Progress
Messages
You can limit or suppress the messages that give details of
setting changes and adjustment progress and results by
setting a display mode.
The conditions under which messages are displayed and
their correspondence with the display mode are as follows:
Setting change confirmation/adjustment progress messages
and display modes
Y: Message is displayed.
N: Message is not displayed.
1) This is also displayed for about 3 seconds when the SHUTTER selector is
set to ON.
Changing the display mode
The currently set display mode appears on the VF DISP 1
page of the USER menu. To change it, proceed as follows.
1
Follow steps 1 and 2 in 6-2-2 “Selecting the Display
Items” on page 85, until the VF DISP 1 page of the
USER menu appears on the screen.
2
Turn the MENU knob to move the b mark to “VF
DISPLAY MODE”, and press the MENU knob.
The b mark on the left of “VF DISPLAY MODE”
changes to a z mark and the z mark on the left of the
setting changes to a ? mark.
3
Turn the MENU knob until the desired display mode
appears, and press the MENU knob.
The z mark on the left of “VF DISPLAY MODE”
changes to a
b mark and the ? mark on the left of the
setting changes to a z mark.
4
To end the menu operation, set the MENU ON/OFF
switch to OFF or close the cover of the menu operating
section.
6-2-4 Setting the Marker Display
Use the MARKER 1 page of the USER menu to switch the
display of the center and safety zone markers on or off and
to select whether the area indicated by the safety zone
marker is 80%, 90% or 100% of the screen area.
1
Set the MENU ON/OFF switch to ON.
The last accessed menu page appears on the screen.
2
Turn the MENU knob until the MARKER 1 page
appears, and press the MENU knob to select the page.
You can set the following items on the MARKER 1
page.
Message
display
condition Message Display
mode
setting
1 2 3
When the filter
selection has
been changed ND : n, CC : m (where n =
1, 2, 3, 4, m = A, B, C, D) N N Y
When the gain
setting has been
changed GAIN : n (where n = -3dB,
0dB, 3dB, 6dB, 9dB,12dB,
18dB, 24dB, 30dB, 36dB,
42dB, 48dB) N N Y
When the
setting of the
WHITE BAL
switch has been
changed WHITE : n (where n = A
CH, B CH, PRESET) or
ATW : RUN N N Y
When the
OUTPUT/DCC
selector has
been set to DCC
ON or OFF DCC : ON (or OFF) N Y Y
When the
shutter speed
and mode
setting has been
changed
1)
SS : 1/100 (PDW-510/530)
or 1/60 (PDW-510P/530P)
(or 1/125, 1/250, 1/500,
1/1000, 1/2000,ECS, SLS) N Y Y
When the black
or white balance
has been
adjusted E.g. WHITE : OK N Y Y
Item Description
MARKER Not to display all markers, set to OFF.
CANCEL/PRST /
ESCAPE switch
MENU knob MENU ON/OFF switch
U07 MARKER 1
MARKER : OFF
CENTER : OFF
SAFETY ZONE : OFF
SAFETY AREA : 90%
ASPECT : OFF
ASPECT SELECT : 4:3
ASPECT MASK : OFF
ASPECT MASK LVL : 1/4
100% MARKER : OFF
TOP