Sony Ericsson PDW-530P - Manual (Page 95)

Cha
p
te
r 6
Men
u
Dis
pla
y
s
and
Det
a
iled Se
tt
ing
s
95
6-3 Adjustments and Settings from Menus
3
Turn the MENU knob to move the b mark to “REAR
BNC OUT SEL”, and press the MENU knob.
The b mark on the left of “REAR BNC OUT SEL”
changes to a z mark and the z mark on the left of the
setting changes to a ? mark.
4
Turn the MENU knob to change the desired setting,
and press the MENU knob.
The z mark on the left of the selected item changes to
a
b mark and the ? mark on the left of the setting
changes to a z mark.
5
To end the menu operation, set the MENU ON/OFF
switch to OFF or close the cover of the menu operating
section.
6-3-3 Setting the Color Temperature
Manually
You can adjust the value of the white balance manually by
setting the color temperature.
Proceed as follows.
1
Holding down the MENU knob, move the MENU ON/
OFF switch from OFF to ON.
The TOP menu appears.
2
Turn the MENU knob to move the b mark to
“PAINT”, and press the MENU knob.
If this is the first time the PAINT menu has been
displayed, the CONTENTS page appears. If the menu
has been used before, the last accessed page appears.
3
If the CONTENTS page is displayed, turn the MENU
knob to move the
b mark to WHITE, and press the
MENU knob to display the WHITE page.
If a different page is displayed, turn the MENU knob
until the WHITE page appears, and press the MENU
knob to select the page.
The above table shows the adjustment of the white
balance of channel A.
Items followed by “<B>” are used to adjust the white
balance of channel B.
4
Turn the MENU knob to move the b mark to the item
you want to set, and press MENU knob.
The b mark on the left of the selected item changes to
a z mark and the z mark on the left of the setting
changes to a ? mark.
5
Turn the MENU knob to change the setting, and press
the MENU knob.
The z mark on the left of the selected item changes to
a
b mark and the ? mark on the left of the setting
changes to a z mark.
To set other items, go back to step 3.
6
To end the menu operation, set the MENU ON/OFF
switch to OFF or close the cover of the menu operating
section.
Item Description
LCD BRIGHT <L> Adjusts the LCD brightness when the
LCD switch is in the L position.
LCD BRIGHT <H> Adjusts the LCD brightness when the
LCD switch is in the H position.
LCD COLOR Adjusts the color saturation of the LCD.
i.LINK SBP2
MODE Selects whether or not to use the
i.LINK connector SBP2 interface.
REAR BNC OUT
SEL Selects the type of the video signal to
be output from the VIDEO OUT
connector.
SDI : Outputs the SDI signal. When
SDI is selected, connect the
VIDEO OUT connector to the SDI
IN connector of the video monitor.
VBS: Outputs the analog composite
video signal. When VBS is
selected, connector the VIDEO
OUT connector to the VIDEO IN
connector of the video monitor.
This setting allows you to save the
power.
Item Description
COLOR TEMP
<A> Sets the color temperature for the
desired value. Adjust the value while
looking at the real image because error
tends to be bigger for adjustment of
high color temperature.
COLOR FINE <A> Adjusts the value more precisely when
the color temperature adjustment
through COLOR TEMP is not
satisfactory.
R GAIN <A> Only the value of R GAIN is changed.
B GAIN <A> Only the value of B GAIN is changed.
D5600K Sets the color temperature to
approximately 5600 K.
P02 WHITE
COLOR TEMP <A>: 3200
COLOR FINE <A>: 0
R GAIN <A>: 0
B GAIN <A>: 0
D5600K <A>: OFF
COLOR TEMP <B>: 3200
COLOR FINE <B>: 0
R GAIN <B>: 0
B GAIN <B>: 0
D5600K : OFF