Sherwood P-965 - Manual (Page 61)

ENGLISH
61
• Each time these buttons are pressed , the mode
changes as follows :
CALL : Select this to recall the channel levels
memorized into preset memory .
SAVE : Select this to memorize the channel levels
adjusted in the CH LEVEL TRIM menu or in
“Adjusting the current channel levels”
procedure on page 32.
• You can recall the memorized channel levels
whenever you want or can memorize the channel
levels adjusted in the CH LEVEL TRIM men, etc.
into preset memory.
STANDBY POWER ON
MAIN PAGE FAV
MUTE
CH. SET
VOL
RETURN
DISP
MI
OSD/MENU
1 STEREO
CH/ ADJUST
2 3
4 5 6
7 8 9
0 ENT
M2 M3
DSP DECODE DSP
STANDBY POWER ON
MAIN PAGE FAV
MUTE
CH. SET
VOL
RETURN
DISP
MI
OSD/MENU
1 STEREO
CH/ ADJUST
2 3
4 5 6
7 8 9
0 ENT
M2 M3
DSP DECODE DSP
RNC-510
To recall the channel levels memorized into preset memory or to memorize
the channel levels adjusted in the CH LEVEL TRIM menu, etc.
To memorize the adjusted channel levels into preset memory.
To adjust the current channel levels as desired.
To adjust LFE (Low Frequency Effect) levels included in Dolby Digital,
DTS and MPEG program sources.
, : S e l e c t
R E T U R N : B a c k E N T E R : C a l l
C H L E V E L S E T U P
P R E S E T 1 : C A L L
P R E S E T 1 T R I M
P R E S E T 2 : C A L L
P R E S E T 2 T R I M
C H L E V E L T R I M
L F E L E V E L T R I M
STANDBY POWER ON
MAIN PAGE FAV
MUTE
CH. SET
VOL
RETURN
DISP
MI
OSD/MENU
1 STEREO
CH/ ADJUST
2 3
4 5 6
7 8 9
0 ENT
M2 M3
DSP DECODE DSP
RNC-510
R E T U R N : B a c k , : S e l e c t
F L : - - - - - - - - - - - - : 0 dB
F C : - - - - - - - - - - - - : 0 dB
F R : - - - - - - - - - - - - : 0 dB
S R : - - - - - - - - - - - - : 0 dB
B R : - - - - - - - - - - - - : 0 dB
B L : - - - - - - - - - - - - : 0 dB
S L : - - - - - - - - - - - - : 0 dB
S W : - - - - - - - - - - - - : 0 dB
P R E S E T 2 T R I M
Press the CURSOR UP( )/DOWN( )
buttons to select the PRESET 1 or
PRESET 2 .
1
Press the CURSOR
LEFT(
)/RIGHT( ) buttons to select
the desired mode, then press the ENTER
button.
2
SETTING THE CH LEVEL SETUP
When selecting the PRESET 1 or
PRESET 2
• You can adjust the channel levels directly in the PRESET TRIM menu and can memorize them into preset
memory.
Press the CURSOR UP( )/DOWN( ) buttons to select the PRESET 1TRIM or PRESET 2 TRIM,
then press the ENTER button.
1
When selecting the PRESET 1 TRIM or PRESET 2 TRIM
Example) When the PRESET 2 TRIM is selected .