KTI Networks NS-32LB451A11 - Manual (Page 17)

11
Insignia 32" LCD TV/Blu-ray Combo, 1080p
www.insigniaproducts.com
Aiming the remote control
To use the remote control:
Point the remote control directly at your TV/Blu-ray
combo, within a 60° angle horizontally (30° to either
side) and within 30° vertically of the remote control
sensor on the front of your TV/Blu-ray combo, and
within 15 feet (4.6 meters) of your TV/Blu-ray
combo.
Programming your universal Insignia remote
control
To program your remote control:
1 Find the codes for the devices you want to
program in “Remote control codes” on page 66
and write them down or highlight them.
2 Turn on the device (for example, a DVD player)
and, if needed, load media such as a DVD.
3 Press the device button on the TV remote for the
device that you want to program (TV, STB, or
AUX).
4 Press and hold SET until the red LED blinks
twice, then release.
5 Enter the first five-digit code for the device and
brand that you want to program. The LED blinks
once as each digit is entered. If the code is valid,
the LED blinks twice.
6 Aim the remote at the device and press
(power). The device should turn off. If it does
not, repeat Steps 3 through 5, trying each code
for your brand until you find one that works. If
you cannot find a code that works, see
“Searching for your code” below.
7 Repeat Steps 1 to 5 for the other devices you
want to control. For future reference, write down
each working device code.
Searching for your code
If your device does not respond to the remote
control after trying all codes listed for your brand, or
if your brand is not listed, try searching for your
code.
To search for your code:
1 Turn on the device you want to control.
2 Press the device button on your TV remote
control (TV, STB, or AUX) once.
3 Press and hold SET until the red LED blinks
twice, then release.
4 Enter 9 9 1. The LED blinks twice.
5 Press the number that matches your device
type.
• 0—Cable converters, video accessories,
satellite receivers
• 1—TVs
• 2—VCRs, DVD players, Blu-ray Disc players
• 3—Audio amplifiers, audio amplifiers/tuners,
CD players
6 Aim the remote at the device and press
(power). The remote sends IR codes from its
library to the selected device, starting with the
most popular code first. If the device responds,
go to Step 8.
7 If the device does not respond, press CH and
the remote tests the next code for that device
type. Continue to press CH
until the device
turns off.
8 Now that you have found the correct code, press
SET to save the code that worked for your
device. The LED blinks twice to indicate that the
code has been saved.
9 To search for other device codes, repeat Steps 1
to 8.
Checking the codes
If you have set up the remote using the procedure
in “Searching for your code” on page 11, you may
need to find out which five-digit code is operating
your equipment.
To find out which code is assigned to your TV
(for example):
1 Press TV once.
2 Press and hold SET until the red LED blinks
twice, then release.
3 Enter 9 9 0. The LED blinks twice.
Caution
Do not expose the remote control to liquids, direct
sunlight, or shock.
Notes
• Objects between the remote control and the
remote control sensor may block the remote
control signal.
• The range of the remote control may be
diminished if direct sunlight or other strong
light is shining at the remote control sensor. In
this case, change the angle of the lighting, move
your TV/Blu-ray combo, or operate the remote
control closer to the remote control sensor.
Note
If the LED does not blink twice, repeat steps 2 to 4
and try entering the code again.
15 feet
(4.6 meters)
Note
Press CH to try the previous code.