Lincoln Electric POWER MIG SVM167-A - Manual (Page 22)

ACCESSORIES C-2 C-2
POWER MIG® 215
DRIVE ROLL KITS
Refer to Table C.1 for various drive roll kits that are
available for the POWER MIG® 215.The item in Bold
is supplied standard with the POWER MIG® 215.
TABLE C.1
3/64" (1.2 mm) ALUMINUM
FEEDING KIT (K1703-1)
This kit helps push feeding aluminum through standard
machine feeder and gun. It provides gun and wire drive
conversion parts to weld with 3/64" (1.2 mm) aluminum
wire. 5356 alloy aluminum wire is recommended for
best push feeding performance.
Kit includes drive rolls and wire guide plate for the wire
drive, liner and two contact tips for the gun, along with
installation instructions.
READI-REEL ADAPTER (K363P)
The K363P Readi-Reel Adapter mounts to the 2" spin-
dle. It is needed to mount the 22-30 lb. Readi-Reels.
DUAL CYLINDER MOUNTING KIT
(K1702-1)
Permits stable side-by-side mounting of two full size
(9" dia. x 5' high) gas cylinders with “no lift” loading.
Simple installation and easy instructions provided.
Includes upper and lower cylinder supports, wheel
axles and mounting hardware.
SMALL SPOOL SPINDLE ADAPTER
(K468)
The K468 spindle adapter allows the use of 8" diame-
ter small spools.
Wire Size Drive Roll Kit
.023”-.030” (0.6-0.8 mm) KP1696-030S
Solid
.035” (0.9 mm) KP1696-035S
Steel
.045” (1.2 mm) KP1696-045S
Cored
.035” (0.9 mm) KP1697-035C
.045” (1.2 mm) KP1697-045C
Aluminum 3/64” (1.2 mm) KP1695-3/64A
ALTERNATIVE MAGNUM GMAW
GUN AND CABLE ASSEMBLIES
The following Magnum 250L gun and cable assemblies
are separately available for use with the POWER
MIG® 215. Each is rated 200 amps 60% duty cycle
and is equipped with the integrated connector, twist-
lock trigger connector, fixed nozzle and insulator, and
includes a liner, diffuser, and contact tips for the wire
sizes specified:
TABLE C.2
MAGNUM GUN CONNECTION KIT
(Optional K466-6)
Using the optional K466-6 Magnum Connection kit for
the POWER MIG® permits use of standard Magnum
200, 300 or 400 gun and cable assemblies.
SPOOL GUN AND ADAPTER KIT
(K1809-1)
The K1809-1includes the Magnum 250SG Spool gun
and the adapter kit for connecting the spool gun to the
POWER MIG® 215.
The Adapter Kit provides toggle switch selection
between the machine’s use with its feeder gun or the
spool gun for same polarity welding with different wire
and gas processes.
The kit includes a spool gun adapter module assembly
with a single connecting plug and trigger switch, a rear
gas inlet, fitting hose, solenoid valve assembly, and
mounting hardware with installation and operation
instructions.
Remove all input power to the POWER MIG® 215
before installing the Spool Gun and Kit.
WARNING
English Wire Metric Wire
Length Part No. Size Size
10' (3.0 m) K533-1
12' (3.6 m) K533-2 .035 – .045" 0.9 – 1.2 mm
15' (4.5 m) K533-3
10' *3.0 m) K533-4
12' (3.6 m) K533-5 .025 – .030" 0.6 – 0.8 mm
15' (4.5 m) K533-6
Return
to
Section
T
OC
Return
to
Section
T
OC
Return
to
Section
T
OC
Return
to
Section
T
OC
Return
to
Master
T
OC
Return
to
Master
T
OC
Return
to
Master
T
OC
Return
to
Master
T
OC