Gun handle disassembly, Accessories and replacement parts for magnum, 250l gun & cable assemblies – Lincoln Electric POWER MIG SVM167-A User Manual
Page 28: Table d.2, Maintenance
MAINTENANCE
D-4
D-4
POWER MIG® 215
GUN HANDLE DISASSEMBLY
The internal parts of the gun handle may be
inspected or serviced if necessary.
The gun handle consists of two halves that are
held together with a collar on each end. To open
up the handle, turn the collars approximately 60
degrees counterclockwise (the same direction
as removing a right hand thread) until the collar
reaches a stop. Then pull the collar off the gun
handle. If the collars are difficult to turn, position
the gun handle against a corner, place a screw-
driver against the tab on the collar and give the
screwdriver a sharp blow to turn the collar past
an internal locking rib.
Counterclockwise
English
Metric
Description
Part No.
Size
Size
CABLE LINER
For 15' (4.5 m) or
KP1934-2
.025 – .030"
0.6 – 0.8 mm
shorter Cable
KP1934-1
.035 – .045"
0.9 – 1.2 mm
KP1955-1
3/64"
1.2 mm
(Alum. wire)
(Alum. wire)
CONTACT TIPS
Standard Duty KP2020-6B1
.025"
0.6 mm
KP2020-7B1
.030"
0.8 mm
KP2020-1B1*
.035"
0.9 mm
KP2020-2B1
.045"
1.2 mm
Heavy Duty KP2021-1B1
.035"
0.9 mm
KP2020-2B1
.045"
1.2 mm
Tapered KP2022-5B1
.025"
0.6 mm
KP2022-6B1
.030"
0.8 mm
KP2022-1B1
.035"
0.9 mm
KP2022-2B1
.045"
1.2 mm
Tab (For Aluminum) KP2010-5B1
3/64"
1.2 mm
(Alum. Wire)
(Alum. Wire)
GAS NOZZLES
Fixed (Flush)
KP1931-1
3/8"
9.5 mm
KP1931-2 *
1/2"
12.7 mm
KP1931-3
5/8"
15.9 mm
Fi
(Recessed)
KP1930-1
3/8"
9.5 mm
KP1930-2
1/2"
12.7 mm
KP1930-3
5/8"
15.9 mm
Requires: Gas
Diffuser As'bly
KP2026-3 *
.025 – .045"
0.6 – 1.2 mm
Adjustable Slip-On
KP1935-2
1/2"
12.7 mm
KP1935-1
5/8"
15.9 mm
Requires:
Nozzle Insulator
KP2025-1
As’bly
Requires:
Gas Diffuser
KP2026-2
.025 – .030"
0.6 – 0.8 mm
As’bly
KP2026-1
.035 – .045"
0.9 – 1.2 mm
Gasless Nozzle
KP1947-1 ∆
(For Innershield)
GUN TUBE ASSEMBLIES
Standard (60°)
KP2015-1 *
45°
KP2041-1
TABLE D.2
ACCESSORIES AND EXPENDABLE REPLACEMENT PARTS
FOR MAGNUM 250L GUN AND CABLE ASSEMBLIES
*
Included with POWER MIG® 215
∆ Requires KP2026-1 Gas Diffuser Assembly.