Extron Electronics MTPX Plus Series Setup Guide - Manual (Page 22)

Refer also to the
MTPX Plus User’
s Manual
at
www
.extron.com
.
Refer also to the
MTPX Plus User’
s Manual
at
www
.extron.com
.
Command ASCII command
(host to switcher)
Response
(switcher to host)
Additional description
IP setup
Set IP address EX2^ CI } Ipi X2^]
Read IP address E CI } X2^]
Set subnet mask EX2^ CS } Ips X2^]
Read subnet mask E CS } X2^]
Set gateway IP address EX2^ CG } Ipg X2^]
Read gateway IP address E CG } X2^]
Set DHCP on or off EX2& DH } Idh X2&]
Read DHCP on/off status E DH } X2&]
Set verbose mode EX2* CV } Vrb X2*]
Read verbose mode E CV } X2*]
Configure current port timeout E 0* X2( TC } Pti0* X2(]
Read current port timeout E 0TC } X2(]
Configure global IP port timeout E 1* X2( TC } Pti1* X2(]
Read global IP port timeout E 1TC } X2(]
N
X2^
= IP address nnn .nnn.nnn.nnn
X2&
= DHCP 0 =1 off, 1 = on
X2* = Verbose mode 0 = clear/none (default for Telnet connection)
1 = verbose mode (default for RS-232/RS-422 connection)
2 = tagged responses for queries
3 = verbose mode and tagged for queries
X2(
= Port timeout interval 1 (= 10 seconds) - 65000 (default is 30 = 300 seconds = 5 minutes)
Installing and Starting the Contr
ol Pr
ogram
Another way to operate the switcher
, to set the skew
adjustments, the level and peaking, and the output pr
e-peaking
(see "Optimizing the video", beginning on page 4-18), is via the W
indows
® -based Matrix Switchers Contr
ol Pr
ogram.
This pr
ogram is contained on the Extr
on Softwar
e Pr
oducts
DVD (included with the switcher). Run this pr
ogram on a
PC connected to a serial port (
i
,
j
, and
m
on pages 2-5 and
2-6), Ethernet port (
k
), or USB port (
n
) on the switcher
. The
pr
ogram must be installed on a W
indows-based computer and
cannot be r
un fr
om the DVD.
N
For
details
on
operating
the
pr
ogram,
refer
to
the
MTPX Plus User's Manual
, chapter
5,
“Matrix
Softwar
e”
.
Installing the pr
ogram
N
To
run
this
pr
ogram
while
your
computer
is
connected
to
an
MTPX
Plus
128
Configuration
(USB)
port,
use
version
7.7
or
newer
of
the
Matrix
Switchers
Contr
ol
Pr
ogram.
1.
Insert the DVD into the drive. The Extr
on softwar
e DVD
window should appear automatically
.
N
If
the
window
does
not
self-open,
run
Launch.exe
fr
om
the
DVD.
The Extr
on softwar
e DVD window appears.
2.
Click the
S
of
tw
ar
e tab.
3.
Scr
oll to the Matrix Switchers pr
ogram and click
In
st
al
l.
MTPX P
lus Series • Remote Contr
o
l and Optimizing the V
ideo
Remote
Contr
ol
and
Optimizing
the
V
ideo,
cont’d
4-14
MTPX P
lus Series • Remote Contr
o
l and Optimizing the V
ideo
4-15