Extron Electronics MTPX Series User Guide - Manual (Page 85)

4-5 MTPX Twisted Pair Matrix Switchers • Programmer’s Guide
PRELIMINAR
Y
Command/Response Table for SIS Commands
Symbol definitions
]
= CR/LF (carriage return/line feed) (hex 0D 0A)
}
= Carriage return (no line feed, hex 0D))
•
= Space character
E
= Escape key (hex 1B)
X!
= Input number (for tie) 00 – (maximum number of inputs for your model) (00 = untied)
X@
= Output number 01 – (maximum number of outputs for your model)
X#
= Input number 01 – (maximum number of inputs for your model)
X$
= Audio/RS-232 input type 0 = audio 1 = RS-232
X%
= Pre-peakable output number MTPX 168 01 – 02
MTPX 816, MTPX 1616, MTPX 3216 01 – 04
MTPX 1632, MTPX 3232 01 – 08
X^
= Mute, pre-peaking, Lock mode, power supply 0 = off/mode 0/not OK
1 = on/mode 1/OK
2 = mode 2
X&
= Local video output number 1 or 2 (matrix sizes 1632 and larger)
N
X&
is applicable to matrix sizes 1632 and larger only.
X*
= Local output sync polarity 0 = H- / V- (default)
1 = H+ / V-
2 = H- / V+
3 = H+ / V+
4 = No sync processing (composite, S-video, YUV)
X(
= Local audio output number 1 – 4 (matrix sizes 1616 and smaller)
1 – 8 (matrix sizes 1632 and larger)
X1)
= Volume adjustment range 0 – 64 (1 dB/step except for 0-to-1, which is 22 dB)
(default = 64 [0dB])
(See the table on page 4-8.)
X1!
= Audio gain 0 – 24 (1 dB/step)
X1@
= Numeric dB value –18 to +24 (45 steps of gain or attenuation) (Default = 0 dB)
X1#
= Audio attenuation 1 – 18 (1 dB/step)
X1$
= Global preset # 0 - 32 (0 = current configuration)
X1%
= Name 12 characters maximum for input, output, and global preset names
Upper- and lower-case alphanumeric characters and
_ / and spaces are valid.
N The following characters are invalid in the name: {space} ~ , @ = ‘ [ ] { } < > ’ “ ; : | \ and ?.
X1^
= Mute: 0 = not muted
2 = audio mute
X1&
= Local input select DIP switch status 0 = RJ-45 position, 1 = local input position
X1*
= Input level/peaking status 0 = not within threshold, 1 = within threshold
X1(
= Baud rate 9600, 19200, 38400, 115200
X2)
= Parity O dd, even, none, mark, space (Only the first letter is required.)
X2!
= Data bits 7, 8
X2@
= Stop bits 1, 2
X2#
= Port type 0 = RS-232, 1 = RS-422
X2$
= Number of inputs 8, 16, or 32
X2%
= Number of outputs 8, 16, or 32
X2^
= Part number 68-nnn-nn
X2&
= Firmware version number to second decimal place (x.xx)
X2*
= Verbose firmware version-description-upload date/time See the Query firmware version (verbose) command on page 4-14.
X2(
= Voltage Positive or negative voltage and magnitude
X3)
= Internal temperature Degrees Fahrenheit
X3!
= Fan speed RPM