Pach and Company AeGIS 4000P Manual - Manual (Page 20)

Pach and Company Page 12
AeGIS 4000P Chapter 3. Programming
70
DIRECT CALL
FORWARDING
IS USED IF
A DEDICATED
PHONE LINE IS
USED OR IF
YOU WANT TO
FORWARD THE
CALL
MANUALLY.
NOTE:
INTERCOM
MODE IS
DISABLED IF
A PHONE
NUMBER IS
PROGRAMMED
ON FUNCTION
CODE 70
Step 1 Entering The Programming
Mode: Press 0 and # simultaneously
then release. If you are in the
programming mode, proceed to step 2.
Step 2 Enter the 4-digit Master
Code (factory default is 0000) and you
will hear “One Short Beep”. If you
entered an invalid master code you will
hear “One Long Beep”, repeat step
1. Should your master code become
lost or forgotten see Reset Master
Code.
Step 3 Enter 65 then #, you will
hear “One Short Beep”.
Step 4 Enter another Function Code
to program another parameter; other-
wise press
∗ to exit and you will hear
“Three Short Beeps”.
Step 1 Entering The Programming
Mode: Press 0 and # simultaneously
then release. If you are in the
programming mode, proceed to step 2.
Step 2 Enter the 4-digit Master
Code (factory default is 0000) and you
will hear “One Short Beep”. If you
entered an invalid master code you will
hear “One Long Beep”, repeat
step 1. Should your master code
become lost or forgotten Reset Master
Code.
Step 3 Enter 70 then #, you will
hear “No Beep”.
Step 4 Enter the phone number you
want to forward the call up to 11-digit
then press #, you will hear “One Short
Beep”.
Step 5 Enter another Function Code
to program another parameter; other-
wise press
∗ to exit and you will hear
“Three Short Beeps”.
Step 1 Press 0 and ∗
simultaneously then release.
Step 2 Press 0 then # to delete
telephone number, you will hear
“Three Short Beeps”. Now, the
AeGIS 4000P is reset to “Intercom
Mode”.
Step 3 Press # and you will hear
“One Short Beep”.
Step 4 Enter 65 then press #, you
will hear “One Short Beep”.
Step 5 Enter another function code
to program different parameter or exit
the program by pressing
∗ ∗ and you
will hear “Three Short Beeps”.
Step 1 Pick up the phone and wait
for dial tone.
Step 2 Press # # and you will hear
“One Short Beep”.
Step 3 Press # and you will hear
“One Short Beep”.
Step 4 Enter 70 then press #, you
will hear “No Beep”.
Step 5 Enter the non-indexed call
forwarding phone number up to 11-
digit you will hear “One Short Beep”.
Step 6 Enter another function code
to program a different parameter or
exit the program by pressing
∗ ∗ and
you will hear “Three
Short B
eeps”.
Step 1 Pick up the phone and wait
for dial tone.
Step 2 Press # # and you will hear
“One Short Beep”.
Step 3 Press 6 and you will hear
“Three Short Beeps”, and the system
disconnects the call.
Step 2 Press # then enter a valid
master code and you will hear:
• “One Short Beep”, the master code
is accepted then press # and you will
hear “One Short Beep” .
• “One Long Beep”, the master code
is rejected and the connection will be
disconnected.
Step 3 Press # to enter into the
programming mode and you will hear
“One Short Beep” or
∗∗ to hang-up
the call.
Step 4 Enter 65 then press #, you
will hear “One Short Beep”.
Step 5 Enter another function code
to program different parameter or exit
the program by pressing
∗ ∗ and you
will hear “Three Short Beeps”.
Step 1 Call to the AeGIS 4000P
system (you must know the system’s
phone number), you will hear: “One
Short Beep”, the gate is locked.“Two
Short Beeps”, the gate is unlocked.
Step 2 Press # then enter a valid
master code and you will hear:
• “One Short Beep”, the master code
is accepted then press # and you will
hear “One Short Beep” .
• “One Long Beep”, the master code
is rejected and the connection will
be disconnected.
Step 3 Press # to enter into the
programming mode and you will hear
“One Short Beep” or
∗∗ to hang-up
the call.
Step 4 Enter 70 then press #, you
will hear “No Beep”.
Step 5 Enter the non-indexed call
forwarding phone number up to 11-
digit you will hear “One Short Beep”.
Step 6 Enter another function code
to program a different parameter or
exit the program by pressing
∗ ∗ and
you will hear “Three Short Beeps.
Step 1 Call to the AeGIS 4000P
system (you must know the system’s
phone number), you will hear: “One
Short Beep”, the gate is locked. “Two
Short Beeps”, the gate is unlocked.
Step 2 Press # then enter a valid
master code and you will hear:
• “One Short Beep”, the master code
is accepted then press # and you will
hear “One Short Beep”.
Function Local Programming Premise Phone Remote Phone
Program
Direct Call
Forwarding
Delete Direct
Call
Forwarding