Pach and Company AeGIS 4000P Manual User Manual
Page 25
92
TALK TIME
(10-90 seconds)
THE SYSTEM
WILL BE
DISCONNECTED
ACCORDING TO
THE TALK TIME
PROGRAMMED.
93
LOCK OUT
COUNT
(03-09)
THE SYSTEM
WILL BE
DISABLED FOR
50 SECONDS
AFTER INVALID
CODES HAVE
BEEN ENTERED
ACCORDING TO
THE NUMBER
OF LOCKOUT
COUNT
PROGRAMMED.
the door is already unlocked you will
hear “One Short Beep” or
• Enter 0 to Lock and you will hear
“One Long Beep” then “One Short
Beep”.
Step 5
Enter another Function Code
to program another parameter other-
wise press
∗ to exit and you will hear
“Three Short Beeps”.
Step 1
Entering The Programming
Mode: Press 0 and # simultaneously
then release. If you are in the
programming mode, proceed to step 2.
Step 2
Enter the 4-digit Master
Code (factory default is 0000) and you
will hear “One Short Beep”. If you
entered an invalid master
code
you will hear “One Long Beep”,
repeat step 1. Should your master
code become lost or forgotten see
Reset Master Code.
Step 3
Enter 92 then #, you will
hear “One Short Beep”.
Step 4
Enter the talk-time value
(10 – 90 seconds) then press #, you
will hear “One Short Beep”.
Step 5
Enter another Function Code
to program another parameter other-
wise press
∗ to exit and you will hear
“Three Short Beeps”.
Step 1
Entering The Programming
Mode: Press 0 and # simultaneously
then release. If you are in the pro-
gramming mode, proceed to step 2.
Step 2
Enter the 4-digit Master
Code (factory default is 0000) and you
will hear “One Short Beep”. If you
entered an invalid master code you will
hear “One Long Beep”, repeat
step 1. Should your master code
become lost or forgotten see Reset
Master Code.
Step 3
Enter 93 then #, you will
hear “One Short Beep”.
Step 4
Enter a new lockout count
value (3-9) then press #, you will hear
“One Short Beep”.
Step 5
Enter another Function Code
to program another parame
ter
other-
wise press
∗ to exit and you will
hear
“Three Short Beeps”.
Step 6
Enter another function code
to program a different parameter or
exit the program by pressing
∗ ∗ and
you will hear “Three Short Beeps”.
Step 1
Pick up the phone and wait
for a dial tone.
Step 2
Press # # and you will hear
“One Short Beep”.
Step 3
Press # and you will hear
“One Short Beep”.
Step 4
Enter the Function Code 92
then press #, you will hear “One Short
Beep”.
Step 5
Enter the talk time value
(10 –90 seconds) then press #, you
will hear “One Short Beep”.
Step 6
Enter another function code
to program a different parameter or
exit the program by pressing
∗ ∗ and
you will hear “Three Short Beeps”.
Step 1
Pick up the phone and wait
for a dial tone.
Step 2
Press # # and you will hear
“One Short Beep”.
Step 3
Press # and you will hear
“One Short Beep”.
Step 4
Enter the Function Code 93
then press #, you will hear “One Short
Beep”.
Step 5
Enter the lockout count
(03 – 09) then press #, you will hear
“One Short Beep”.
Step 6
Enter another function code
to program a different parameter or
exit the program by pressing
∗ ∗ and
you will hear “Three Short Beeps”.
then “One Short Beep”. If you hear
“One Short Beep”, means the door
is already unlocked or
•
Press 0 (to lock) then press #, you
will hear “One Long Beep” then
“One Short Beep”.
Step 5
Enter another function code
to program a different parameter or
exit the program by pressing
∗ ∗ and
you will hear “Three Short Beeps”.
Step 1
Call to the AeGIS 4000P
system (you must know the system’s
phone number), you will hear: “One
Short Beep”, the gate is locked. “Two
Short Beeps”, the gate is unlocked.
Step 2
Press # then enter a valid
master code and you will hear:
• “One Short Beep”, the master code
is accepted then press # and you will
hear “One Short Beep”.
• “One Long Beep”, the master code
is rejected and the connection will be
disconnected.
Step 3
Enter the Function Code 92
then press #, you will hear “One Short
Beep”.
Step 4
Enter the talk time value
(10 –90 seconds) then press #, you
will hear “One Short Beep”.
Step 5
Enter another function code
to program a different parameter or
exit the program by pressing
∗ ∗ and
you will hear “Three Short Beeps”
.
Step 1
Call to the AeGIS 4000P
system (you must know the system’s
phone number), you will hear: “One
Short Beep”, the gate is locked. “Two
Short Beeps”, the gate is unlocked.
Step 2
Press # then enter a valid
master code and you will hear:
• “One Short Beep”, the master code
is accepted then press # and you
will hear “One Short Beep”.
• “One Long Beep”, the master code
is rejected and the connection will be
disconnected.
Step 3
Enter the Function Code 93
then press #, you will hear “One Short
Beep”.
Step 4
Enter the lockout count
(03 – 09) then press #, you will hear
“One Short Beep”.
Function
Local Programming
Premise Phone
Remote Phone
Pach and Company
Page 17
AeGIS 4000P
Chapter 3. Programming