Pach and Company AeGIS 4000P Manual - Manual (Page 23)

88
SELECT
AUTOMATIC
CALL
FORWARDING
FUNCTION
NUMBER
89
SET AUTOMATIC
CALL
FORWARDING
TIME OR
HANG-UP TIME
THE SYSTEM
WILL HANG-UP
ACCORDING TO
THE TIME
SELECTED ON
FUNCTION
CODE 89 IF THE
TENANT DOES
NOT PICK UP
THE CALL
Step 3 Enter 87 then #, you will
hear “One Short Beep”.
Step 4
• Press 1 then # to enable and you will
hear “One Short Beep” or
• 0 then # to disable, and you will hear
“One Short Beep”.
Step 5 Enter another Function Code
to program another parameter other-
wise press
∗ to exit and you will hear
“Three Short Beeps”.
Step 1 Entering The Programming
Mode: Press 0 and # simultaneously
then release. If you are in the pro-
gramming mode, proceed to step 2.
Step 2 Enter the 4-digit Master
Code (factory default is 0000) and you
will hear “One Short Beep”. If you
entered an invalid master code you will
hear “One Long Beep”, repeat
step 1. Should your master code
become lost or forgotten see Reset
Master Code.
Step 3 Enter 88 then #, you will
hear “One Short Beep”.
Step 4 Enter Index Number (71-72)
then #, you will hear “One Short
Beep”.
Step 5 Enter another Function Code
to program another parameter
otherwise press
∗ to exit and you will
hear “Three Short Beeps”.
Step 1 Entering The Programming
Mode: Press 0 and # simultaneously
then release. If you are in the pro-
gramming mode, proceed to step 2.
Step 2 Enter the 4-digit Master
Code (factory default is 0000) and you
will hear “One Short Beep”. If you
entered an invalid master code you will
hear “One Long Beep”, repeat
step 1. Should your master code
become lost or forgotten see Reset
Master Code.
Step 3 Enter 89 then #, you will
hear “One Short Beep”.
Step 5
• Press 1 (to enable) then press #, you
will hear “One Short Beep” or
• Press 0 (to disable) then press #,
you will hear “One Short Beep”.
Step 6 Enter another function code
to program a different parameter or
exit the program by pressing
∗ ∗ and
you will hear “Three
Short Beeps”.
Step 1 Pick up the phone and wait
for a dial tone.
Step 2 Press # # and you will hear
“One Short Beep”.
Step 3 Press # and you will hear
“One Short Beep”.
Step 4 Press 88 then #, you will
hear “One Short Beep”.
Step 5 Press 71 or 72 then press #,
you will hear “One Short Beep” .
Step 6 Enter another function code
to program a different parameter or
exit the program by pressing
∗ ∗ and
you will hear “Three Short Beeps”.
Step 1 Pick up the phone and wait
for a dial tone.
Step 2 Press # # and you will hear
“One Short Beep”.
Step 3 Press # and you will hear
“One Short Beep”.
Step 4 Press 89 then #, you will
hear “One Short Beep”.
Step 5 Press 15-90 (15 seconds-90
seconds) then press #, you will hear
“One Short Beep”.
Step 3 Press # to enter into the
programming mode and you will hear
“One Short Beep” or
∗∗ to hang-up
the call.
Step 4 Press 87#, you will hear
“One Short Beep” , then
• Press 1 (to enable) then press #,
you will hear “One Short Beep” or
• Press 0 (to disable) then press #,
you will hear “One Short Beep”.
Step 5 Enter another function code
to program a different parameter or
exit the program by pressing
∗ ∗ and
you will hear “Three Short Beeps”.
Step 1 Call to the AeGIS 4000P
system (you must know the system’s
phone number), you will hear: “One
Short Beep”, the gate is locked.“Two
Short Beeps”, the gate is unlocked.
Step 2 Press # then enter a valid
master code and you will hear:
• “One Short Beep”, the master
code is accepted then press #
and you will hear “One Short
Beep”.
• “One Long Beep”, the master
code is rejected and the
connection will be disconnected.
Step 3 Press # to enter into the pro-
gramming mode and you will hear
“One Short Beep” or
∗∗ to hang-up
the call.
Step 4 Press 88 then #, you will
hear “One Short Beep”.
Step 5 Press 71 or 72 then press #,
you will hear “One Short Beep”.
Step 6 Enter another function code
to program a different parameter or
exit the program by pressing
∗ ∗ and
you will hear “Three Short Beeps”.
Step 1 Call to the AeGIS 4000P
system (you must know the system’s
phone number), you will hear: “One
Short Beep”, the gate is locked. “Two
Short Beeps”, the gate is unlocked.
Step 2 Press # then enter a valid
master code and you will hear:
• “One Short Beep”, the master code
is accepted then press # and you will
hear “One Short Beep”.
• “One Long Beep”, the master code
is rejected and the connection will be
disconnected.
Function Local Programming Premise Phone Remote Phone
Pach and Company Page 15
AeGIS 4000P Chapter 3. Programming