Pach and Company AeGIS 4000P Manual User Manual

Page 27

Advertising

SYSTEM

ANSWER MODE

ENABLE OR

DISABLE THE

AUTO ANSWER

MODE. IF

DISABLE THE

SYSTEM WILL
NOT ANSWER
AN INCOMING

CALL FROM THE

OUTSIDE LINE.

DO NOT

DISTURB MODE

DISABLE OR

ENABLE THE

SYSTEM TO

CALL

“One Short Beep”. Refer to
Chapter 5 System’s Operation.

Step5

Enter another Function Code

to program another parameter
otherwise press

∗ to exit and you will

hear “Three Short Beeps”.

Step 1

Entering The Programming

Mode: Press 0 and # simultaneously
then release. If you are in the
programming mode, proceed to step 2.

Step 2

Enter the 4-digit Master

Code (factory default is 0000) and you
will hear “One Short Beep”. If you
entered an invalid master code you will
hear “One Long Beep”, repeat
step 1. Should your master code
become lost or forgotten see Reset
Master Code.

Step 3

Enter 96 then #, you will

hear “One Short Beep”.

Step 4

Enter 0 (system answer is

disabled) or 1, 2, 3 or….9 (system will

answer a remote call on 1st ring, 2nd

ring, 3rd ring…9th ring) then press #
and you will hear “One Short Beep”.

Step 5

Enter another Function Code

to program another parameter
otherwise press

∗ to exit and you will

hear “Three Short Beeps”.

Step 1

Entering The Programming

Mode: Press 0 and # simultaneously
then release. If you are in the
programming mode, proceed to step 2.

Step 2

Enter the 4-digit Master

Step 3

Enter 97 then #, you will

hear “One Short Beep”.

Step 4

Enter

0 to disable Do not Disturb Mode

(mode 0 is factory default setting)

1 to enable Do not Disturb Mode

(system will not call to a premise or
remote location)

then press #, you will hear “One Short
Beep”.

Step 5

Enter another Function Code

to program another parameter
otherwise press

∗ to exit and you will

The system number of rings to
answer a remote call can be
programmed from 1 to 9 rings or it
can also be disabled. You must
program the System Answer
Mode at the front panel

Step 1

Pick up the phone and wait

for a dial tone.

Step 2

Press # # and you will hear

“One Short Beep”.

Step 3

Press # and you will hear

“One Short Beep”.

Step 4

Enter the Function Code 97

then press #, you will hear “One Short
Beep”.

Step 5

Enter 0 (to disable) or 1 (to

enable) then press #, you will hear
“One Short Beep”.

Step 6

Enter another function code

to program a different parameter or
exit the program by pressing

∗ ∗ and

you will hear “Three
Short Beeps”.

Step 5

Enter another function

code to program a different parameter
or exit the program by pressing

∗ ∗

and you will hear “Three Short
Beeps”.

The system number of rings to
answer a remote call can be
programmed from 1 to 9 rings or it
can also be disabled. You must
program the System Answer
Mode at the front panel.

Step 1

Call to the AeGIS 4000P

system (you must know the system’s
phone number), you will hear: “One
Short Beep”, the gate is locked. “Two
Short Beeps”, the gate is unlocked.

Step 2

Press # then enter a valid

master code and you will hear:
• “One Short Beep”, the master code

is accepted then press # and you will
hear “One Short Beep”.

• “One Long Beep”, the master code

is rejected and the connection will be
disconnected.

Step 3

Enter the Function Code 97

then press #, you will hear “One Short
Beep”.

Step 4

Enter 0 (to disable) or 1 (to

enable) then press #, you will hear
“One Short Beep”.

Step 5

Enter another function code

to program a different parameter or
exit the program by pressing

∗ ∗ and

you will hear “Three Short Beeps”.

Function

Local Programming

Premise Phone

Remote Phone

Pach and Company

Page 19

AeGIS 4000P

Chapter 3. Programming

Advertising

Popular Brands

Popular manuals