Pach and Company AeGIS 4000P Manual - Manual (Page 24)

Pach and Company Page 16
AeGIS 4000P Chapter 3. Programming
90
MANUAL
UNLOCK OR
LOCK RELAY 1
(DOOR 1)
91
MANUAL
UNLOCK OR
LOCK RELAY 2
(DOOR 2)
Step 4 Select the Automatic Call
Forwarding Time (15 – 90 seconds)
then #, you will hear “One Short
Beep”.
Step 5 Enter another Function Code
to program another parameter other-
wise press
∗ to exit and you will hear
“Three Short Beeps”.
Step 1 Entering The Programming
Mode: Press 0 and # simultaneously
then release. If you are in the
programming mode, proceed to step 2.
Step 2 Enter the 4-digit Master
Code (factory default is 0000) and you
will hear “One Short Beep”. If you
entered an invalid master code you will
hear “One Long Beep”, repeat
step 1. Should your master code
become lost or forgotten see Reset
Master Code.
Step 3 Enter 90 then #, you will
hear “One Short Beep”.
Step 4
• Enter 1 to Unlock Relay 1 (Door 1)
and you will hear “Two Long
Beeps” then “One Short Beep”. If
the door is already unlocked you will
hear “One Short Beep” or
• Enter 0 to Lock and you will hear
“One Long Beep” then “One Short
Beep”.
Step 5 Enter another Function Code
to program another parameter other-
wise press
∗ to exit and you will hear
“Three Short Beeps”.
Step 1 Entering The Programming
Mode: Press 0 and # simultaneously
then release. If you are in the
programming mode, proceed to step 2.
Step 2 Enter the 4-digit Master
Code (factory default is 0000) and you
will hear “One Short Beep”. If you
entered an invalid master code you will
hear “One Long Beep”, repeat
step 1. Should your master code
become lost or forgotten see Reset
Master Code.
Step 3 Enter 91 then #, you will
hear “One Short Beep”.
Step 4
• Enter 1 to Unlock Relay 1 (Door 1)
and you will hear “Two Long
Beeps” then “One Short Beep”. If
Step 6 Enter another function code
to program a different parameter or
exit the program by pressing
∗ ∗ and
you will hear “Three Short Beeps”.
Step 1 Pick up the phone and wait
for a dial tone.
Step 2 Press # # and you will hear
“One Short Beep”.
Step 3 Press # and you will hear
“One Short Beep”.
Step 4 Press 90 then #, you will
hear “One Short Beep”.
Step 5
• Press 1 (to unlock hold) then press #,
you will hear “Two Long Beeps”
then “One Short Beep”. If you hear
“One Short Beep”, means the door
is unlocked or
• Press 0 (to lock) then press #, you
will hear “One Long Beep” then
“One Short Beep”.
Step 6 Enter another function code
to program a different parameter or
exit the program by pressing
∗ ∗ and
you will hear “Three Short Beeps”.
Step 1 Pick up the phone and wait
for a dial tone.
Step 2 Press # # and you will hear
“One Short Beep”.
Step 3 Press # and you will hear
“One Short Beep”.
Step 4 Press 91 then #, you will
hear “One Short Beep”.
Step 5
• Press 1 (to unlock hold) then press #,
you will hear “Two Long Beeps”
then “One Short Beep”. If you hear
“One Short Beep”, means the door
is unlocked or
• Press 0 (to lock) then press #, you
will hear “One Long Beep” then
“One Short Beep”.
Step 3 Press 89 then #, you will
hear “One Short Beep”.
Step 4 Press 15-90 (15 seconds-90
seconds) then press #, you will hear
“One Short Beep”.
Step 5 Enter another function code
to program a different parameter or
exit the program by pressing
∗ ∗ and
you will hear “Three Short Beeps”.
Step 1 Call to the AeGIS 4000P
system (you must know the system’s
phone number), you will hear: “One
Short Beep”, the gate is locked. “Two
Short Beeps”, the gate is unlocked.
Step 2 Press # then enter a valid
master code and you will hear:
• “One Short Beep”, the master code
is accepted then press # and you will
hear “One Sh
ort Beep”.
• “One Long Beep”, the master code
is rejected and the connection will be
disconnected.
Step 3 Press 90 then #, you will
hear “One Short Beep”.
Step 4
• Press 1 (to unlock hold) then press
#, you will hear “Two Long Beeps”
then “One Short Beep”. If you hear
“One Short Beep”, means the door
is already unlocked or
• Press 0 (to lock) then press #, you
will hear “One Long Beep” then
“One Short Beep”.
Step 5 Enter another function code
to program a different parameter or
exit the program by pressing
∗ ∗ and
you will hear “Three Short Beeps”.
Step 1 Call to the AeGIS 4000P
system (you must know the system’s
phone number), you will hear: “One
Short Beep”, the gate is locked. “Two
Short Beeps”, the gate is unlocked.
Step 2 Press # then enter a valid
master code and you will hear:
• “One Short Beep”, the master code
is accepted then press # and you will
hear “One Sh
ort Beep”.
• “One Long Beep”, the master code
is rejected and the connection will be
disconnected.
Step 3 Press 91 then #, you will
hear “One Short Beep”.
Step 4
• Press 1 (to unlock hold) then press
#, you will hear “Two Long Beeps”
Function Local Programming Premise Phone Remote Phone