State GTS-710-PIEA - Manual (Page 34)

- 34 -
The dark squares indicate the direction
the dipswitches should be set to.
TEMPERATURE SETTINGS
 There are 8 preset temperatures that you can select from by changing the dipswitch settings
on the computer board.
 The temperature has been preset at the factory to 120ºF (49ºC).
 If you desire to change the set temperature with dipswitches, please refer to the diagram on
below. These temperatures are available: 100ºF, 115ºF, 120ºF, 135ºF, 145ºF, 155ºF, 165ºF,
and 185ºF.
 If you desire a hot water temperature other than the 8 preset settings, please purchase the
optional temperature remote controller (part No. 9007603005 (TM-RE30)).
 With this optional remote controller you can set the temperature from 100ºF to 185ºF with
various increments.
 Please read the instructions carefully prior to installing the remote controller, as failure to do
so could damage the temperature controller and/or the water heater, which will void the
warranty.
 Turn off the power supply to the heater before changing the dipswitch
settings.
 Only change the switches with the dark squares. The dark squares indicate
which direction the dipswitch should be set to.
 DO NOT set to 185 ºF if you use your water heater in a recirculation system.
This will cause damage to the heater and void the warranty.
To change dipswitch settings for
temperatures, locate the left
bank of dipswitches the lower of
7-Seg LED.
DO NOT adjust the right bank of
dipswitches.
7-Seg LED
Left bank of
dipswitches
Right bank of
dipswitches
Temperature Settings Left bank of Dipswitch
DIRE
O U T
TMP3
TMP2
TMP1
1
2
3
4
5
6
7
8
MODE
N O
1
2
3
4
5
6
7
8
N O
1
2
3
4
5
6
7
8
N O
1
2
3
4
5
6
7
8
N O
1
2
3
4
5
6
7
8
N O
1
2
3
4
5
6
7
8
N O
1
2
3
4
5
6
7
8
N O
1
2
3
4
5
6
7
8
N O
C) (38
100 F
C) (46
115 F
C) (57
135 F
C) (63
145 F
C) (68
155 F
C) (74
165 F
C) (85
185 F
C) (49
120 F
Default
M S T
D-PRT
DIRE
O U T
TMP3
TMP2
TMP1
MODE
M S T
D-PRT
DIRE
O U T
TMP3
TMP2
TMP1
MODE
M S T
D-PRT
DIRE
O U T
TMP3
TMP2
TMP1
MODE
M S T
D-PRT
DIRE
O U T
TMP3
TMP2
TMP1
MODE
M S T
D-PRT
DIRE
O U T
TMP3
TMP2
TMP1
MODE
M S T
D-PRT
DIRE
O U T
TMP3
TMP2
TMP1
MODE
M S T
D-PRT
DIRE
O U T
TMP3
TMP2
TMP1
MODE
M S T
D-PRT
100 ºF
(38 ºC) 115 ºF
(46 ºC)
120 ºF
(49 ºC)
Default 135 ºF
(57 ºC) 145 ºF
(63 ºC) 165 ºF
(74 ºC) 155 ºF
(68 ºC) 185 ºF
(85 ºC)
Temperature Settings <Left bank of dipswitches>