State GTS-710-PIEA - Manual (Page 44)

- 44 -
OPTIONAL ITEMS
1. Temperature remote controller: 9007603005
(TM-RE30)
The temperature remote controller
has two functions. It allows the
output temperature from the water
heater to be adjusted within the
range of 100 °F to 185 °F, and it
also works as a diagnostic tool that
will give a concise error code whenever there is a
problem with the unit. The temperature options are
100 °F, 105 °F, 110 °F, 115 °F, 120 °F, 125 °F, 130 °F,
135 °F, 140 °F, 145 °F, 150 °F, 155 °F, 160 °F, 165 °F,
170 °F, 175 °F, 180 °F and 185 °F. See the
troubleshooting section for information on possible
error codes.
2. Multi-unit controller: 9007675005
(TM-MC01)
The multi-unit controller can control
a maximum of 20 water heaters,
from 24,000 BTU to 4,800,000
BTU. It also works as a diagnostic
tool that will give a concise error
code whenever there is a problem
with the unit. Usage of this
controller requires having the
9007603005 (TM-RE30) remote
controller.
3. 4” Backflow preventer and F-F adaptor:
9007996005
There are two functions available for
this adaptor which can be connected
with the water heater and NovaVent
venting line and prevents the
backflow of air through the exhaust
vent. This helps prevent harmful
exhaust gases from entering the
home, as well as helping to prevent
the unit from freezing in areas where
cold air can be blown or drawn into the exhaust
system. Install this adaptor in accordance with the
installation instructions that are packaged with the
adaptor and any applicable codes.
4. Vent cap: 9007676005 (TM-VC32)
The vent cap is for outdoor
installation with the 710 (T-M32)
water heater. The cap is
installed on the top of the unit,
instead of connecting an
exhaust vent pipe. The cap will
prevent any debris that might be in the environment
from entering the unit and causing damage or a fire
hazard, as well as preventing rain or other weather
from entering the unit.
5. Direct-vent conversion kit: 9007668005
(TM-DV32)
This kit can be used to convert the
710 (T-M32) from a conventional
vent system to a direct-vent (or
sealed combustion) system. This is
a CSA tested conversion kit. Install
this conversion kit in accordance
with the manufacturer’s installation
instructions and any applicable codes.
6. Pipe cover: 9007672005 (TM-PC32)
The pipe cover protects the plumbing
pipes to the 710 (T-M32) from
unexpected adjustments. This pipe
cover is fixed to the bottom of the
water heater, which hides the
plumbing and improves the visual
aspects of the whole installation for the water heater.
7. Sidewall vent terminator (Hood) and Wall thimble:
They are used when venting out through the wall. These terminations are special
stainless steel vents for gas applications and are UL listed as Categoly ll, lll and lV.
For different wall thickness, there are
two ranges of lengths available.
(Refer to the NovaVent brochure
for details.) Install these vent
terminations in accordance with
their installation instructions and
any applicable local codes.
Covering wall thickness Part #
Terminator Hood 9007999005
Wall Thimble 4 - 7 in. 9008345005
Wall Thimble 5 - 10 in. 9008346005
Termination + Thimble 4 - 7 in. 9008004005
Termination + Thimble 5 – 10 in. 9008005005
Wall Thimble
Terminator Hood