Loading the batteries, Operating range of remote control – Pioneer VSX-828-K User Manual

Page 10

Advertising
background image

Controls and displays

1

1

10

65

7

4

• When the front speaker is set at SMALL in the Speaker

Setting (or automatically via the Auto MCACC setup)

and the X.Over is set above 150 Hz, the subwoofer

channel level will be adjusted by pressing

BASS +/–

(

page 53

).

10

Number buttons and other component controls

Use the number buttons to directly select a radio frequency

(

page 34

) or the tracks on a CD, etc. There are other buttons

that can be accessed after

is pressed. (For example

MIDNIGHT

, etc.)

EQ

– Press to switch on/off Acoustic Calibration EQ

setting (

page 39

).

PHASE

– Press to switch on/off Phase Control (

page 39

).

SIGNAL SEL

– Press to select the audio input signal of the

component to play back (

page 27

).

S.RETRIEVER

– Press to restore CD quality sound to

compressed audio sources (

page 39

).

SB CH

(VSX-828 only) – Press to select ON, AUTO or OFF

the surround back channel (

page 40

).

CH SELECT

– Press repeatedly to select a channel, then

use

LEV +/–

to adjust the level (

page 53

).

LEV +/–

– Use to adjust the channel level.

MIDNIGHT

– Switches to Midnight or Loudness listening

(

page 41

).

SPEAKERS

– See

Switching the speaker terminal on

page 15

.

DIMMER

– Dims or brightens the display. The brightness

can be controlled in four steps.
During ECO mode, the brightness switches between 2

levels. If the dimmest level is selected, DIMMER will be

shown on the display. (Mode other than ECO: 4 levels, ECO

mode: 2 levels)

+Favorite

– Press while a song is being played back or

stopped. The selected song is then registered in the

Favorites folder (

page 46

).

11

SOURCE

Press to turn on/off other components connected to the

receiver (

page 60

).

12

TV CONTROL buttons

These buttons are dedicated to control the TV assigned to the

TV

button. Thus if you only have one TV to hook up to this

system assign it to the

TV

button (

page 61

).

– Use to turn on/off the power of the TV.

INPUT

– Use to select the TV input signal.

CH +/–

– Use to select channels.

VOL +/–

– Use to adjust the volume on your TV.

13

ECO

Switches between ECO Mode 1/ECO Mode 2. When ECO

Mode is turned ON, the display will go dark (

page 38

).

14

VOLUME +/–

Use to set the listening volume.

15

MUTE

Mutes/unmutes the sound.

16

DISP

Switches the display of this unit. The listening mode, sound

volume, Speaker System (VSX-828) setting or input name can

be checked by selecting an input source.

The Speaker System setting may or may not be displayed,

depending on the input source you have selected.

Loading the batteries

The batteries included with the unit are to check initial

operations; they may not last over a long period. We

recommend using alkaline batteries that have a longer life.

WARNING

Do not use or store batteries in direct sunlight or other

excessively hot place, such as inside a car or near a heater.

This can cause batteries to leak, overheat, explode or catch

fire. It can also reduce the life or performance of batteries.

CAUTION

Incorrect use of batteries may result in such hazards as

leakage and bursting. Observe the following precautions:

-

Never use new and old batteries together.

-

Insert the plus and minus sides of the batteries properly

according to the marks in the battery case.

-

Batteries with the same shape may have different

voltages. Do not use different batteries together.

-

When disposing of used batteries, please comply with

governmental regulations or environmental public

institution’s rules that apply in your country/area.

-

When inserting the batteries, make sure not to damage

the springs on the battery’s (–) terminals. This can cause

batteries to leak or overheat.

Operating range of remote control

The remote control may not work properly if:

There are obstacles between the remote control and the

receiver’s remote sensor.

Direct sunlight or fluorescent light is shining onto the

remote sensor.

The receiver is located near a device that is emitting

infrared rays.

The receiver is operated simultaneously with another

infrared remote control unit.

RECEIVER

30°

7 m

30°

VSX-828_SYXE8_En.book 10 ページ 2013年3月1日 金曜日 午前9時16分

Advertising
This manual is related to the following products: