Pioneer VSX-828-K - Manual (Page 54)

Home Menu 7 7
54
65
7
4 4 Confirm your selected setup option.
The test tones will start after you press
ENTER . After the
volume increases to the reference level, test tones will be
output.
5 Adjust the level of each channel using / .
If you selected Manual, use / to switch speakers. The
Auto setup will output test tones in the order shown on-
screen:
Adjust the level of each speaker as the test tone is
emitted.
Note
• If you are using a Sound Pressure Level (SPL) meter, take
the readings from your main listening position and adjust
the level of each speaker to 75 dB SPL (C-weighting/slow
reading).
• The subwoofer test tone is output at low volumes. You may
need to adjust the level after testing with an actual
soundtrack.
6
When you’re finished, press RETURN .
You return to the Manual SP Setup menu.
Tip
• You can change the channel levels at any time by press
, then press CH SELECT and LEV +/– on the
remote control. You can also press CH SELECT and use /
 to select the channel, and then use / to adjust the
channel levels.
Speaker Distance
For good sound depth and separation from your system, you
need to specify the distance of your speakers from the
listening position. The receiver can then add the proper delay
needed for effective surround sound.
1 Select ‘Manual SP Setup’ from the Home Menu.
2 Select ‘Speaker Distance’ from the Manual SP Setup
menu.
3 Adjust the distance of each speaker using / .
You can adjust the distance of each speaker in 0.03 m
increments.
4 When you’re finished, press RETURN .
You return to the Manual SP Setup menu.
The Input Assign menu
Assigns input function for analog audio input terminal and
component video input terminal (component video input
terminal for VSX-828 only).
• For the assignment of the digital signal inputs, see
Selecting the audio input signal on page 27 .
Analog Input
ANALOG IN1 audio input terminal is assigned to CD under
factory settings, but this can be changed to TV input.
1 Select ‘Input Assign’ from the Home Menu.
2 Select ‘Analog Input’ from the Input Assign menu.
3 Select the desired input option for the ANALOG IN1
audio input terminal.
4 When you’re finished, press RETURN .
You return to the Input Assign menu.
Note
• When playing analog input audio, switch to the CD or TV
input menu, press and press SIGNAL SEL
several times to choose A (Analog). (see Selecting the audio
input signal on page 27 )
Component Input (VSX-828 only)
COMPONENT VIDEO IN1 input terminal is assigned to DVD
under factory settings, but this can be changed to SAT/CBL
input.
1 Select ‘Input Assign’ from the Home Menu.
2c . Channel Level
Please Wait . . .20
Caution
Loud test tones
will be output.
Return
Test Tone [ Manual ]
2 c . C h a n n e l L ev e l
F ro n t L
C e n t e r
F ro n t R
S u r ro u n d R
S u r r. B a ck R
S u r r. B a ck L
S u r ro u n d L
S u b wo o fe r
R e t u r n
[ 0 d B ]
[ 0 d B ]
[ 0 d B ]
[ – – – ]
[ – – – ]
[ 0 d B ]
[ 0 d B ]
0 d B
RECEIVER
2 . M a nu a l S P S e t u p
R e t u r n
a . S p e a k e r S e t t i n g
b . X . O v e r
c . C h a n n e l L ev e l
d . S p e a k e r D i s t a n c e
2 d . S p e a k e r D i s t a n c e
F ro n t L
C e n t e r
F ro n t R
S u r ro u n d R
S u r r. B a ck R
S u r r. B a ck L
S u r ro u n d L
S u b wo o fe r
R e t u r n
[ 3 m ]
[ 3 m ]
[ 3 m ]
[ – – – – ]
[ – – – – ]
[ 3 m ]
[ 3 m ]
3 m
3 . I n p u t A s s i g n
R e t u r n
a . A n a l o g I n p u t
b . C o m p o n e n t I n p u t
3 a . A n a l o g I n p u t
R e t u r n
A n a l o g C D
VSX-828
RECEIVER
VSX-828_SYXE8_En.book 54 ページ ２０１３年３月１日 金曜日 午前９時１６分