Pioneer VSX-828-K - Manual (Page 25)

Basic Setup 3 3
25
65
7
4
If you have a tripod, use it to place the microphone so that
it’s about ear level at your normal listening position.
Otherwise, place the microphone at ear level using a
table or a chair.
4 Press BD button on the remote control to switch to BD
entry.
5 Press on the remote control, then press the
HOME MENU button.
The Home Menu appears on your TV. Use /// and
ENTER on the remote control to navigate through the
screens and select menu items. Press RETURN to exit
the current menu.
• Press HOME MENU at any time to exit the Home
Menu. If you cancel the Auto MCACC setup at any
time, the receiver automatically exits and no settings
will be made.
• The screensaver automatically starts after three
minutes of inactivity.
6 Select ‘Auto MCACC’ from the Home Menu, then press
ENTER .
• Mic In! blinks when the microphone is not connected
to MCACC SETUP MIC jack.
Try to be as quiet as possible after pressing ENTER . The
system outputs a series of test tones to establish the
ambient noise level.
7 Follow the instructions on-screen.
• Make sure the microphone is connected.
• Make sure the subwoofer is on and the volume is
turned up.
• When using surround back or front height speakers,
turn on the power to the amplifier to which the
surround back or front height speakers are connected,
and adjust the sound level to the desired level (VSX-828
only).
• See below for notes regarding background noise and
other possible interference.
8 Wait for the test tones to finish.
A progress report is displayed on-screen while the
receiver outputs test tones to determine the speakers
present in your setup. Try to be as quiet as possible while
it’s doing this.
• For correct speaker settings, do not adjust the volume
during the test tones.
9 Confirm the speaker configuration.
The configuration shown on-screen should reflect the
actual speakers you have.
• With error messages (such as Too much ambient
noise
) select RETRY after checking for ambient noise
(see Other problems when using the Auto MCACC
setup below ).
If the speaker configuration displayed isn’t correct, use
/ to select the speaker and / to change the
setting. When you’re finished, go to the next step.
If you see an error message (ERR) in the right side
column, there may be a problem with the speaker
connection. If selecting RETRY doesn’t fix the problem,
turn off the power and check the speaker connections.
10 Make sure ‘OK’ is selected, then press ENTER .
If the screen in step 9 is left untouched for 10 seconds
and ENTER is not pressed in step 10, the Auto MCACC
setup will start automatically as shown.
A progress report is displayed on-screen while the
receiver outputs more test tones to determine the
optimum receiver settings for channel level, speaker
distance, X.Over, and Acoustic Calibration EQ.
Tripod
Microphone
RECEIVER
H o m e M e nu
1 . Au t o M C AC C
2 . M a nu a l S P S e t u p
3 . I n p u t A s s i g n
4 . Au t o Pow e r D ow n
5 . H D M I S e t u p
6 . N e t wo r k S t a n d by
7 . M H L S e t u p
8 . S p e a k e r S y s t e m
9 . O S D S e t u p
H o m e M e nu
1 . Au t o M C AC C
2 . M a nu a l S P S e t u p
3 . I n p u t A s s i g n
4 . Au t o Pow e r D ow n
5 . H D M I S e t u p
6 . N e t wo r k S t a n d by
7 . M H L S e t u p
8 . O S D S e t u p
VSX-828 VSX-528
1 . Au t o M C AC C
N ow A n a ly z i n g
E nv i ro n m e n t C h e ck
A m b i e n t N o i s e
S p e a k e r Y E S / N O
R e t u r n
1 . Auto MCACC
Check
Return 10:Next
Front
Center
Surr
Surr. Back
Subwoofer [ YES ]
[ YES ]
[ YES ]
[YESx2]
[ YES ]
1 . Auto MCACC
Check
OK
Return 10:Next
Front
Center
Surr
Subwoofer [ YES ]
[ YES ]
[ YES ]
[ YES ]
OK
VSX-828 VSX-528
1 . Au t o M C AC C
N ow A n a ly z i n g
S u r ro u n d A n a ly z i n g
S p e a k e r S y s t e m
X . O v e r
S p e a k e r D i s t a n c e
C h a n n e l L ev e l
A c o u s t i c C a l E Q
Return
VSX-828_SYXE8_En.book 25 ページ ２０１３年３月１日 金曜日 午前９時１６分