Pioneer DJM-900SRT - Manual (Page 10)

10 En
Connections
Be sure to turn off the power and unplug the power cord from the power outlet whenever making or changing connections.
Connect the power cord after all the connections between devices have been completed.
Be sure to use the included power cord.
Refer to the operating instructions for the component to be connected.
 When creating a DVS (Digital Vinyl System) combining a computer, audio interface, etc., be careful in connecting the audio interface to this unit’s input terminals and in
the settings of the input selector switches.
Also refer to the operating instructions of the DJ software and audio interface.
Rear panel
OFF
RETURN
L
L
L
1 GND 2 HOT
3 COLD
L
R
L
L
IN
CH3 CH4
CH1 CH2
R
R
R
R
L
R
R
PHONO PHONO PHONO
CH 4 CH 3
CD/LINE
L
R
PHONO
CH 1
CD/LINE
SIGNAL GND SIGNAL GND
TRS
CD/LINE
MASTER1 MASTER2 REC OUT BOOTH
MIC2 MIDI OUT
DIGITAL
MASTER
OUT
LINK
L
R
CH 2
CD/LINE
(MONO)
L R (MONO)
SEND
POWER
AC IN
ON
1 3 4 3 4 4 3 4 3 5 5 6 7 8 2
d e a b h 9 c g f
1 POWER button (page 14)
Turns this unit’s power on and off.
2 RETURN terminals (page 11)
Connect to the output terminal of an external effector. When the [L (MONO)]
channel only is connected, the [L (MONO)] channel input is simultaneously
input to the [R] channel.
3 PHONO terminals (page 11)
Connect to a phono level (MM cartridge) output device. Do not input line level
signals.
To connect a device to the [PHONO] terminals, remove the short-circuit pin plug
inserted in the terminals.
Insert this short-circuit pin plug into the [PHONO] terminals when nothing is
connected to them to cut external noise.
4 CD/LINE terminals (page 11)
Connect to a DJ player or a line level output component.
5 SIGNAL GND terminal (page 11)
Connects an analog player’s ground wire here. This helps reduce noise when the
analog player is connected.
6 MIC2 terminal (page 11)
Connects a microphone here.
7 MIDI OUT terminal (page 11)
Connects this to the MIDI IN terminal on an external MIDI sequencer.
8 Kensington security slot
9 DIGITAL IN terminal (page 11)
Connect these to the digital coaxial output terminals on DJ players, etc. The
sound may be momentarily interrupted when the output signal sampling fre-
quency is switched.
a DIGITAL MASTER OUT terminal (page 11)
Outputs the master channel audio signals.
b LINK terminal (page 11)
Connect these to the LINK terminals on Pioneer DJ players or the LAN ports of
computers on which rekordbox is installed (PRO DJ LINK).
To connect multiple devices, use a switching hub (commercially available).
Use a 100Base-TX-compatible switching hub. Some switching hubs may not
operate properly.
c BOOTH terminals (page 11)
These are output terminals for a booth monitor.
d REC OUT terminals (page 11)
These are output terminals for recording.
e MASTER2 terminals (page 11)
Connect to a power amplifier, etc.
f MASTER1 terminals (page 11)
Connect to a power amplifier, etc.
Be sure to use these as balanced outputs. Be careful not to accidentally
insert the power cord of another unit.
g SEND terminals (page 11)
Connect to the input terminal of an external effector. When the [L (MONO)]
channel only is connected, a monaural audio signal is output.
h AC IN
Connects to a power outlet using the included power cord. Wait until all connec-
tions between the equipment are completed before connecting the power cord.
Be sure to use the included power cord.
WARNING
The short-circuit pin plugs out of the reach of children and infants. If accidentally
swallowed, contact a doctor immediately.