Pioneer CNDV-50MT - Manual (Page 121)

119
Appendix
NAVI/AV
Direction of G sensor is not correct.
Please turn system power off and
check the installation. After check-
ing, please re-boot the system and
press “OK”. Direction of G sensor is set incor-
rectly. See the “Installation Manual” and set
the direction of the Hide-away unit
correctly.
Gyro Sensor is not working properly.
Please consult your dealer or Pioneer
service centre. Abnormal output of Gyrosensor is
detected. Note down the error code shown on
the screen; turn off the power, and
then contact your nearest Pioneer
service facility.
This function is not available now. The screen cannot be displayed with
Vehicle Dynamics Display.
Because the sensor has not been
taught so the sensor information
cannot be acquired. If the sensor learning status reaches
the Sensor Initialising status or
more, the system is ready to be used.
System detected that the vertical
angle of the installation has been
changed. Learning status for Gyro
Sensor has been initialised. If the mounting angle of the Hide-
away unit has been changed. The system initialises the sensor in
order to operate it with the maximum
performance and automatically
starts re-learning.
System detected that the vertical
angle of the installation exceeds the
permission level. Please install the
navigation unit correctly. The navigation unit is installed with
an extreme angle exceeding the limi-
tation of the installation angle. Confirm the installation angle. (The
navigation system must be installed
within +30 degrees to -30 degrees of
the horizontal, or within five degrees
of your vehicle’s direction of travel.)
Route calculation was not possible. Route calculation has failed because
of malfunction of map data, software,
hardware, or disc. •Change the destination.
•Clean the disc.
•Consult the Pioneer Local dealer if
this message persists.
Route calculation was not possible
because the destination is too far. The destination is too far. •Set a destination closer to the start-
ing point.
•Set one or more way points.
Route calculation was not possible
because the destination is too near. The destination or way point(s) is too
close. Set a destination [and way point(s)]
farther from the starting point.
Route calculation was not possible
due to traffic regulations. •The destination or way point(s) are
in a Control Traffic Zone (CTR) and
the route calculation is hampered.
•Your vehicle is currently in a Control
Traffic Zone (CTR) and the route cal-
culation is hampered. •Set a destination and way point(s)
outside the CTR if you know where
the restricted area is.
•Try the destination or way point(s)
away from the currently set points to
some extent.
•Drive your vehicle to an unre-
stricted area and reset the destina-
tion and way point(s).
Route calculation was not possible
because no guidance can be pro-
vided around the destination or the
starting point. The destination, way point(s), or
starting point are in an area where
no road exists (e.g. a mountain) and
the route calculation is impossible. •Set a destination and way point(s)
on roads.
•Reset the destination after you drive
the vehicle to any road.
There is no route to the destination. The destination or way point(s) are in
an isolated island, etc. without a ferry
and the route calculation is impossi-
ble. Change the destination.
Your journey can not avoid the speci-
fied area. If route setting cannot avoid speci-
fied Areas to Avoid. If the current route is not desired, set
destination or way points that do not
pass through the Areas to Avoid.
The route could not avoid the speci-
fied area.
Toll road has not been avoided. If the route to the destination (or way
point) cannot be established by
bypassing toll roads (including toll
areas) and Areas to Avoid. If the current route is not desired, set
destination or way points that do not
pass through toll roads (including
toll areas) and Areas to Avoid.
Ferry has not been avoided. In case a ferry route was included in
the route to the destination or way
points even though “Avoid Ferry”
was set to On. If the current route is not desired, set
destination or way points that do not
pass through a ferry route.
Message When What to do