JLG M4069 ANSI Service Manual - Manual (Page 22)

SECTION 2 - GENERAL
2-2 – JLG Lift– 3121122
2.2 SERVICE AND GUIDELINES
General
The following information is provided to assist you in the
use and application of servicing and maintenance proce-
dures contained in this book.
Safety and Workmanship
Your safety, and that of others, is the first consideration
when engaging in the maintenance of equipment. Always
be conscious of weight. Never attempt to move heavy
parts without the aid of a mechanical device. Do not allow
heavy objects to rest in an unstable position. When raising
a portion of the equipment, ensure that adequate support
is provided.
Cleanliness
IT IS GOOD PRACTICE TO AVOID PRESSURE-WASHING ELEC-
TRICAL/ELECTRONIC COMPONENTS. IN THE EVENT PRES-
SURE-WASHING THE MACHINE IS NEEDED, ENSURE THE
MACHINE IS SHUT DOWN BEFORE PRESSURE-WASHING.
SHOULD PRESSURE WASHING BE UTILIZED TO WASH AREAS
CONTAINING ELECTRICAL/ELECTRONIC COMPONENTS, JLG
INDUSTRIES, INC. RECOMMENDS A MAXIMUM PRESSURE OF
750 PSI (52 BAR) AT A MINIMUM DISTANCE OF 12 INCHES (30.5
CM) AWAY FROM THESE COMPONENTS. IF ELECTRICAL/ELEC-
TRONIC COMPONENTS ARE SPRAYED, SPRAYING MUST NOT
BE DIRECT AND BE FOR BRIEF TIME PERIODS TO AVOID HEAVY
SATURATION.
1. The most important single item in preserving the
long service life of a machine is to keep dirt and for-
eign materials out of the vital components. Precau-
tions have been taken to safeguard against this.
Shields, covers, seals, and filters are provided to
keep air, fuel, and oil supplies clean; however, these
items must be maintained on a scheduled basis in
order to function properly.
2. At any time when air, fuel, or oil lines are discon-
nected, clear adjacent areas as well as the openings
and fittings themselves. As soon as a line or compo-
nent is disconnected, cap or cover all openings to
prevent entry of foreign matter.
3. Clean and inspect all parts during servicing or main-
tenance, and assure that all passages and openings
are unobstructed. Cover all parts to keep them
clean. Be sure all parts are clean before they are
installed. New parts should remain in their contain-
ers until they are ready to be used.
Components Removal and Installation
1. Use adjustable lifting devices, whenever possible, if
mechanical assistance is required. All slings (chains,
cables, etc.) should be parallel to each other and as
near perpendicular as possible to top of part being
lifted.
2. Should it be necessary to remove a component on
an angle, keep in mind that the capacity of an eye-
bolt or similar bracket lessens, as the angle between
the supporting structure and the component
becomes less than 90°.
3. If a part resists removal, check to see whether all
nuts, bolts, cables, brackets, wiring, etc., have been
removed and that no adjacent parts are interfering.
Component Disassembly and Reassembly
When disassembling or reassembling a component, com-
plete the procedural steps in sequence. Do not partially
disassemble or assemble one part, then start on another.
Table 2-1. Inspection and Maintenance
Type Frequency
Primary
Responsibility
Service
Qualification
Reference
Pre-Start Inspection
Prior to use each day; or
At each Operator change.
User or Operator User or Operator Operator and Safety Manual
Pre-Delivery
Inspection
Prior to each sale, lease, or
rental delivery.
Owner, Dealer, or User
Qualified JLG
Mechanic
Service and Maintenance
Manual and applicable JLG
inspection form.
Frequent Inspection
In service for 3 months or 150 hours,
whichever comes first; or
Out of service for a period of more than 3
months; or
Purchased used.
Owner, Dealer, or User
Qualified JLG
Mechanic
Service and Maintenance
Manual and applicable JLG
inspection form.
Annual Machine
Inspection
Annually, no later than 13 months from the
date of the prior inspection.
Owner, Dealer, or User
Factory-Trained
Service Technician
(recommended)
Service and Maintenance
Manual and applicable JLG
inspection form.
Preventative
Maintenance
At intervals as specified in the Service and
Maintenance Manual.
Owner, Dealer, or User
Qualified JLG
Mechanic
Service and Maintenance
Manual