Rockwell Automation GV3000/SE AC Drive Ver. 6.06 Hdwe Ref., Installation, and Troubleshooting Manual - Manual (Page 123)

Index Index-1
I
NDEX
Numerics
115 VAC Interface Option Board, 2-21
A
AC disconnect (optional), location of, 2-10
AC input
diodes, checking, 9-9 to 9-10
disconnect, installing, 5-2
fuse, 2-10
isolation transformer, 5-1
line branch circuit fuses, 3-9 to 3-10, 5-2 to 5-4
line transients, avoiding, 5-1
ratings, 2-2
wire sizes, 3-5 to 3-6
wiring, 3-5 to 3-6, 4-1 to 4-9, 5-1 to 5-6
AC line reactors, 5-2
AC output
wiring, 3-5 to 3-6, 4-1 to 4-9, 6-1 to 6-2
Air flow, 3-4
Alarms, 9-1
Altitude requirements, 3-2
Ambient conditions, 3-2, A-2
Analog input
jumper J4 settings, 2-16
wiring, 2-18, 7-2, 7-4, 7-5, 7-11
Analog output
description, 2-11
jumper J17 settings, 2-17
wiring, 7-2, 7-10
Assistance, technical, 1-1
AutoMax Network Option board, 2-20
AutoMax RS-232 Adapter Cable, 2-20
B
Blower transformer taps, changing, 5-6
Braking, snubber resistor, 2-11, 5-1, A-2
wiring, 2-18, 7-3, 7-4, 7-5, 7-16
Branch circuit protection, 5-2
Bus Clamp board
location, 2-8, 2-9
part number, 9-15, 9-16
C
Capacitor board
location, 2-4, 2-5, 2-6
part number, 9-12, 9-13
Capacitors, DC bus, 9-1 to 9-7
Carrier frequency, 2-11, A-1
Closed-loop control,
see Vector Regulation
Conduit plugs, replacing, 4-2
Connector
Operator Interface Module, 2-19
option board, 2-19
RS-232, 2-18
Contactors, installing output, 6-1
Contacts, Form A and Form B, 2-11
Control and Configuration Software, 2-18, 2-21, 3-9
Control source, 7-1
ControlNet Network Option board, 2-20
CS3000 RS-232 Computer Cable, 2-21
CS3000, see Control and Configuration Software
Current Feedback board
location, 2-4, 2-5, 2-6, 2-10
part number, 9-12
Current transformer
location, 2-8, 2-9
part number, 9-15, 9-16
D
DC bus
fuse, 2-8, 2-9, 5-2 to 5-4, 9-15, 9-16
input wiring, 3-5 to 3-6, 4-1 to 4-9, 5-1 to 5-4,
5-6
terminals, 9-3 to 9-7
verifying capacitor voltage, 9-1 to 9-7
Declaration of Conformity, C-1
DeviceNet Network Option Board, 2-21
DeviceNet Network Option board, 2-19
Digital input wiring, 2-18, 7-2, 7-4 to 7-5, 7-12 to
7-16
Digital output wiring, see Status Relays
Dimensions, drive, 3-2 to 3-3
Disconnect, installing AC input, 5-2
Display,
see Keypad/display
Distribution system capacity, AC line, 5-1, A-1