Panasonic NV-J45 Series - Manual (Page 28)

Timer Recording (Cont’d)
1
(1) CHANNEL a 2; DATE
a IIIIIII IIIIIIIII IIIIIIIII a Illlllll m IIIIIII a lllllllli
:ii IIIIIIIII IIIIIII IIIIIIIII a ¡Illlllll a Illlllll a lllllllli
m IIIIIIIII! a Hi III IIIIIIIII a illlllll 2 s- - a III Illli
1 7}- -»h IIIIIII IIIIIIIII a Illlllll E IIIIIIIII a illilli
3 IIIIIIIII a IIIIIIIII M IIIIIIIII m Illlllll a nil lili a illli
3 IIIIIIIII a IIIIIIIII a IIIIIII E] lllllllli 0 Iiiiiii m Illilli
m llllilllll u IIIIIIIII a IIIIII m IIIIIIIII m lllllllli a lllllllli
E IIIIIIIII m IIIIIIIII a illlllll a Illlllll m Illlllll a IIIIIII
m IIIIIIIII llllilllll a Illlllll m illli m IIIIIII a Illlllll
m IIIIIIIII illlllll a IIIIIIIII a IIIIIII a illli a IllllHi
El Jpu Jim a lllllllli
Jilii
'3;STARTTIME Q 4 END TIME
Q d
Q d
0D
□
5 □
6 □
7 L>
Í □
9 □
10 Q
III
ill
m s
□□
□
□
□
□
5 □
fi □
1 □-
a □
9 □
10
□
a
s-
a
E
a
a
a
a
m
m
El
m
iiiiiii
li
IIIIIII
iiiiiiiii
iiiiiiii
iiiiii
iiiii
IIIIIII
m
Iiiiii a mil
illlllll m Illlllll
Hill a lili
Illlllll 0 Illlllll
Illlllll a Illlllll
Illlllll a Illlllll
illli a IIIIIIIII
IIIII m illlllll
lilillll 0 lilillll
miMim ^ Ml
llllilllll m IIIIIII
lllil№ a illilli
TIMER RECORDING BY USING THE
REMOTE CONTROLLER AS DIGITAL
SCANNER
Tracing the Bar Codes
Example: When programming a timer recording for a
programme that will be broadcast on channel
position 4 on the 3rd of the month, from 7:02
to 7:30, trace the bar codes in the order of
the numbered arrows shown.
• Press the Digital Scanner On/Off Button to turn it “ON".
1
Trace the bar code for “CHANNEL".
H --
* D 1 CHANNEL
ON OFF
&
2 Trace the bar code for “DATE”.
3
D
(2 DATE
ON OFF
s-
3 Trace the bar code for “START TIME”.
3
D 3 START TIME
ON OFF
T *nn
t u u
1
4 Trace the bar code for “MIN".
U
I
3
D
ON OFF
m
t U L
7 f iiiHiii
TIMER ON/OFF I CANCEL I CHECK
JÍMJI .□ IIIIII
5 Trace the bar code for “END TIME”.
S' 3 o 4 END TIME
ON
1 n j
I U L .
OFF
T-nn
i - U U
1 B-
_y
6 Trace the bar code for “MIN”.
ON
3 o
OFF
■?
* U L
1 - j n
I J u
7
Trace the bar code for “RECORDING” according to
the desired tape speed.
U
I 3 d
SP
RECORDING
ON OFF
1 n y
t U L
T. i n
I* J U
• The “Bee Bee Bee Bee Beeeeep” sound signals
that the scanner is now ready for data transmission.
• When no sound is heard, read the bar codes once
again.
• If more than one bar code is read in the same
group, only the last code will be effective.
• If the “CANCEL” bar code is read, all bar codes that
have been read so far will be cancelled.
• If you do not trace the bar code for “RECORDING",
the tape speed shown in the Multi-Function Display
will be programmed.
(
28
)