Pioneer VSX-D710S - Manual (Page 17)

Preparations
DTS-ES ON/OFF setting mode (VSX-
D810S/D850S only)
This setting allows you to hear surround back channels
on DTS disc regardless of whether the disc itself is a 5 1
Ch disc or a 6 1 Ch disc Naturally you need to hook up
surround back speakers (see p 13) and set them properly
(see below on this page) in order to hear surround back
channels If you choose ON you will hear surround back
channels with DTS discs If you choose OFF you will not
Choose DTS-ES ON or OFF by using the A
or V buttons
T) r r f * r '1 M Ti r r r r
J.I I _l (.. .J. J m I .LI 1 .J L- . 1 LJI 1
MEMO:
• If you choose none for the surround back speakers setting
later on this page you won’t be able to select ON here
• You’ll only get surround back channel sound when
the receiver is in STANDARD mode (see p 27-29),
DTS-ES is set to ON and the disc is a DTS 5 1/6 1
channel disc
SPEAKERS (Front, Center, Surround)
setting mode
This setting establishes the size and configuration of the
speaker system you have connected So, for example,
here you set whether you have connected surround
speakers or not, and how big they are Selecting “Large”
or “Small” will determine how much bass is sent by the
receiver to the speakers being set
In the display, “F”, “C”, and “S” refer to front, center,
and surround speakers respectively Speaker size is
denoted as “L” for large speakers, “S” for small
speakers, and (asterisk) if no speaker is connected
Choose a speaker setting mode according to
the speakers you hooked up Use the A or V
buttons
The configurations shown below will appear in the
display on the front of the receiver One of them
should match your speaker set up Cycle through the
different possibilities until you find the one that
matches your set up
Press > to advance to the next receiver setting, and
press <J to return to a previous receiver setting
r 1 r
1 L. L
1 r 1
1. .J L
1 t
r 1 .. r
1 L L L. -J .J
t
r 1 r
1 L. L L
5
1
t
F L F K . r 1
-J -J L.
1 t
1 1"
f L L
r: r; r
J J J
t
r
L C
i
F 5 - C * • r r
-.1 J
\ t
F 5 - F 5 - 5 *
i t
c : r . r
r r
„1 L J
r r
.J -J
l t
F L ■ C 1 •
J J
i t
F L - a . r.’ 1
.J L
MEMO:
If the cone size (diameter) of the speaker is larger than 5
inches, please set to Large
SPEAKERS (Surround Back) setting
mode (VSX-D810S/D850S only)
This setting establishes the size of the speaker connected
to the surround back terminal (VSX-D810S/D850S only)
You can choose a surround back speaker and its size or
you can choose to hook a subwoofer to this terminal
Switch the surround back speaker setting
mode according to the size of the speaker
you hooked up Use the A or V buttons
The configurations shown below will appear in the
display on the front of the receiver Choose one
Cycle through the different possibilities until you find
the one that matches your set up
If you select SB SUBWF here you can hook a
subwoofer up to the surround back speaker terminals
(see p 13) In this case the terminals will be used for
this “passive subwoofer” and no surround back
sound will come from these terminals
Press > to advance to the next receiver setting, and
press < to return to a previous receiver setting
MEMO:
• You can only set the surround back speaker to large if
the surround speakers are set to small
• If you choose none for surround speakers (see
previous setup) you won’t be able to select any
surround back speakers either
• If you choose A+B speaker systems no sound is heard
from the “passive subwoofer”
17
En