Futaba 12Z - Manual (Page 106)

106 <Functions of Model Menu (Helicopter Functions)>
PUSH
[Cursor Lever]
Ɣ0RYHPHQWRQWKH
VFUHHQ GLUHFWLRQV
Ɣ3XVKWKHOHYHUWRFDOO
QH[WSDJH
[Data Input Dial]
[Enter Button]
[Return Key]
Ɣ7RKRPH
VFUHHQ
Ɣ7RSUHFHGLQJ
VFUHHQ
MODEL MENU (HELICOPTER)
This section contains information on the
commands that apply to helicopters only. For
instructions on Airplanes and Sailplanes, refer
to the sections pertaining to those aircraft. Each
of these functions can be set independently for
GLIIHUHQWÀLJKWFRQGLWLRQV7RJHWWRWKHVHVHWWLQJV
move the cursor to the desired function and push
the enter button to be entered.
Use the Model Type function in the Linkage
Menu to select the swash type matched to the
fuselage beforehand. If you later change model
types, all settings will be lost.
Also, add flight conditions at the Condition
Select screen before setting the model data at each
function. (Up to 8 conditions can be used)
The AFR function, fuel mixture and other
functions common to all model types, are described
in a separate section.
Model Menu functions (helicopter) list
PIT CURVE:$GMXVWVUHVSRQVHLQGLIIHUHQWÀLJKWFRQGLWLRQV
THR CURVE: Throttle curve and hovering trim adjustment
ACCELERATION: Allows a brief "overload" in response to sudden throttle and pitch commands
THR HOLD: Moves the throttle to idle during autorotation
SWASH MIX: Compensates for each control response
THROTTLE MIX: Compensates for power loss when cyclic applied
PIT to NEEDLE:$GMXVWVUHVSRQVHFXUYHLQGLIIHUHQWÀLJKWFRQGLWLRQV
PIT to RUD: Handles torque changes from pitch angle inputs
FUEL MIXTURE: Commands a second servo to adjust the fuel mixture at the carburetor
GYRO: Used to switch gyro sensitivity
GOVERNOR: Used to switch RPM of the helicopter’s head
To activate/deactivate Condition Hold:
1.Move the cursor to [COND. HOLD].
2.Set the throttle stick lower than
the 1/3 point and push the enter
button to activate/deactivate the
condition hold function.
*See p. 68 for condition hold function details.
*Condition hold operation is displayed.
ﶺﶶ﷌﷊ﶼ ﵺ ﶺ﷊ﶸﶪ
ＲＨ０ ﻚ ﻨＬﻜ０ﻦ
．Ｊ０（６ ﻚ ：６８Ｂ，６０
４Ｂ， ﻚ Ｎ＊０（Ｊ
ＲＮＮＪ＜Ｊ０Ｒ，Ｂ６８
Ｎ６８ＬＢ，ﻞ．Ｊ＜ＪＮ，
４０６Ｆﻞ
ﻚ ：Ｂ＄Ｊ．
，Ｄ０ ﻚ Ｎ＊０（Ｊ
，Ｄ０６，，＜Ｊ ﻚ ：Ｂ＄
ﴶﴸﴸﳜ
ﶺﶶ﷌﷊ﶼ﷤ ﶸﶶﶰﶺ﷒ﶼ
ﴶﴸﳰﴶﴸﳰﴸﴸ
．＆Ｒ．Ｄ ﻚ ：Ｂ＄
，Ｄ０ ﻚ Ｄ６＜Ｌ
﷎ﶸ﷌ ﵺ ﷄﶶﶼ﷌ﶞ ﷂﶸﷄ ﶈ ﶆ ６ＨＨ
ﶺﶶ﷌﷊ﶼ ﵺ ﶺ﷊ﶸﶪ
．＆Ｒ．Ｄ ﻚ ：Ｂ＄
ＲＮＮＪ＜Ｊ０Ｒ，Ｂ６８
４Ｂ，ﻲ：ＪＪＬ＜Ｊ
Ｈ＊Ｊ＜
ﻚ ：Ｂ＄，＊０Ｊ
，Ｄ０ ﻚ Ｄ６＜Ｌ
，Ｄ０６，，＜Ｊ ﻚ ：Ｂ＄
４Ｂ，ﻲ０＊Ｌ
Ｎ６８ＬﻞＤ６＜Ｌ
ﴶﴸﴸﳜ
ﶺﶶ﷌﷊ﶼ﷤ ﶸﶶﶰﶺ﷒ﶼ
ﴶﴸﳰﴶﴸﳰﴸﴸ
Ｆ６（Ｊ０８６０
Ｚ＂０６
﷎ﶸ﷌ ﵺ ﷄﶶﶼ﷌ﶞ ﷂﶸﷄ ﶈ ﶆ ６ＨＨ
ŏ 6HOHFW WKH PRGHO PHQX LFRQ DW WKH KRPH
VFUHHQ DQG FDOO WKH PRGHO PHQX VKRZQ
below by pushing the enter button.
ŏ 8VH WKH FXUVRU OHYHU WR VHOHFW WKH IXQFWLRQ
you want to set and call the setup screen by
pushing the enter button..