Futaba 12Z - Manual (Page 123)

123 <Data>
EXP1/EXP2 curve adjustment
(EXP1 curve)
8VLQJ WKH (;3 FXUYH LV HIIHFWLYH LQ
smoothing starting of the ailerons, elevator,
rudder, etc.
(EXP2 curve)
8VLQJWKH(;3FXUYHLVHIIHFWLYHLQHQJLQH
rise and other engine control.
The curve left and right rates ([RATE A],
>5$7(%@ DQG(;3FXUYHUDWH >(;3$@>(;3
%@  FDQ EH DGMXVWHG LQGLYLGXDOO\ >(;3@ IRU
(;3
The curve can also be offset horizontally
([OFFSET]) in the vertical direction.
[Rate setting]
1. Use the cursor lever to move the cursor
(reverse-video) to the [RATE A], [RATE B],
[EXP A], or [EXP B] setting item.
2. Set the rate by turning the data input dial
to the left or right.
Initial value: +100.0% (rate)/+0.0% (EXP
rate)
A d j u s t m e n t r a n g e : - 2 0 0 . 0 ~ + 2 0 0 . 0 %
(rate)/-100.0~+100.0% (EXP rate)
(When the enter button is pushed for 1 second, the rate is
reset to the initial value.)
[Offsetting the curve horizontally in the
vertical direction]
1. Use the cursor lever to move the cursor
(reverse-video) to the [OFFSET] setting
item.
2. Move the curve in the vertical direction
by turning the data input dial to the left or
right.
Initial value: +0.0%
975FXUYHDGMXVWPHQW
975FXUYH
When this curve is used, when the operating
rudder angle is large such as with acrobatic
models, switching from normal flight to
acrobatic rudder angle is performed without
switch operation.
The curve left and right rates ([RATE A],
[RATE B]) can be adjusted individually. The
curve can also be offset horizontally ([OFFSET])
in the vertical direction.
The VTR curve point position ([P.POS A],
[P.POS B], and rate ([P.RATE A], [P.RATE B])
can be adjusted individually.
[Rate setting]
1. Use the cursor lever to move the cursor
(reverse-video) to the [RATE A] or [RATE B]
setting item.
2. Set the rate by turning the data input dial
to the left or right.
Initial value: +100.0%
Adjustment range: -200.0~+200.0%
(When the enter button is pushed for 1 second, the rate is
reset to the initial value.)
[VTR curve point setting]
1. Use the cursor lever to move the cursor
(reverse-video) to the [P.POS A], [P.POS B],
[P.RATE A], or [P.RATE B] setting item.
2. Set the rate by turning the data input dial
to the left or right.
Initial value: +50% ([P.POS A], [P.POS
B])/+100.0% ([P.RATE A], [P.RATE B])
Adjustment range: +0.0~+100.0%
(When the enter button is pressed for 1 second, the rate is
reset to the initial value.)
*When [P.POS A] or P.POS B] is made large, the curve
point moves to the outside. When [P.RATE A] or [P.RATE
B] is set to +100%, the curve becomes a straight line.
[Offsetting the curve horizontally in the
vertical direction]
1. Use the cursor lever to move the cursor
(reverse-video) to the [OFFSET] setting
item.
2. Move the curve in the vertical direction by
turning the data input dial to the left or right.
Initial value: +0.0%