Futaba 12Z - Manual (Page 127)

127 <Data>
Updating procedure
Note: If the battery fully discharges during
SURJUDP XSGDWLQJ XSGDWLQJ ZLOO IDLO :KHQ
the remaining battery capacity is 50% or
less, always recharge the battery before
updating.
Note: The model data in the transmitter can
be used unchanged after updating, but to
be safe, back up the model data before
updating.
Update switch
Ɣ8SGDWHPRGH
Ɣ1RUPDOPRGH
,QVHUWWKH&)FDUGFRQWDLQLQJWKHXSGDWHÀOH
into the card slot.
2. Use tweezers to switch the slide switch
(update switch) at the side of the card slot in
the up direction.
3. Turn on the transmitter power. About 10
seconds later, the screen shown below will
appear. (To abort updating, turn off the
transmitter power.)
，ｄｂ＀ ﻚ ４０６Ｆ０Ｒ： ﻚ ＊４ＬＲ，Ｊ
．，Ｒ０，﻾ ﻚ ４＊．Ｄ ﻚ ＬＢＲ＜ ﻚ ｀．ＪＮ
*If a CF card is not inserted into the card slot, or the files
needed at updating are not copied to the CF card, the error
message shown below will appear. Turn off the power to the
transmitter and check the CF card.
，ｄｂ＀ ﻚ ４０６Ｆ０Ｒ： ﻚ ＊４ＬＲ，Ｊ
８６ ﻚ ：Ｊ：６０＂ ﻚ ＮＲ０Ｌ
 :KHQ WKH HQWHU EXWWRQ LV SXVKHG DERXW 
seconds, updating starts.
During writing, the bar graph moves to the
right.
，ｄｂ＀ ﻚ ４０６Ｆ０Ｒ： ﻚ ＊４ＬＲ，Ｊ
Ｒ４４＜ＢＮＲ，Ｂ６８ ﻚ ＊４＜６ＲＬＢ：Ｆ
 :KHQ XSGDWLQJ LV FRPSOHWH WKH VFUHHQ
shown below appears.
，ｄｂ＀ ﻚ ４０６Ｆ０Ｒ： ﻚ ＊４ＬＲ，Ｊ
Ｎ６：４＜Ｊ，ＪＬ
6. Turn off the power switch. After the monitor
LED goes off, switch the update switch in the
down direction.
*After the updating above has been completed, turn on the
power and then check the system program version at the
system menu information screen.
Updating
7KH7=WUDQVPLWWHUSURJUDPFDQEHXSGDWHG:KHQIXQFWLRQVDUHDGGHGRULPSURYHGWKHXSGDWH¿OH
FDQEHGRZQORDGHGIURP)XWDEDGHDOHUZHEVLWH&RS\WKHXSGDWH¿OHVWRWKH&)FDUGDQGWKHQXVHWKH
following procedure to update the program.
)87$%$&25325$7,213KRQH    )DFVLPLOH    
0DNXKDUL7HFKQR*DUGHQ%OGJ%)1DNDVH0LKDPDNX&KLED-DSDQ
‹)87$%$&25325$7,21