Futaba 12Z - Manual (Page 111)

111 <Functions of Model Menu (Helicopter Functions)>
PUSH
[Cursor Lever]
Ɣ0RYHPHQWRQWKH
VFUHHQ GLUHFWLRQV
Ɣ3XVKWKHOHYHUWRFDOO
QH[WSDJH
[Data Input Dial]
[Enter Button]
[Return Key]
Ɣ7RKRPH
VFUHHQ
Ɣ7RSUHFHGLQJ
VFUHHQ
Normal Curve Idle-up 1 Curve Idle-up 2 Curve
Ɣ7KURWWOH&XUYH ([DPSOH
The curves shown below were created by using
the Line mode and inputting the data of the 5 points
0% (low side), 25%, 50% (center), 75%, 100%
(high) side at each condition. They were created by
reducing the number points of the line to 5. When
actually creating a curve, enter the data specified
per the aircraft (or the reference value).
*For a description of the curve creation method, see the
description at the back of this manual.
Curve setting examples
Throttle Hover trim
The Throttle Hover trim setup screen can be called from the THR Curve setup screen.
The Throttle Hover function trims the throttle
near the hovering point. Normally, use it with
hovering conditions. Changes in rotor speed
accompanying changes in the temperature,
humidity, and other flight conditions can be
trimmed. Adjust the throttle so that rotor rotation is
most stable. More delicate trimming is also possible
by using this function along with the Hover Pitch
function.
Setting method
ŏ:KHQXVLQJWKHKRYHULQJ QRUPDO FRQGLWLRQRQO\
VZLWFKWKHJURXSPRGHWRWKHVLQJOHPRGHDQG
PDNHWKHVHWWLQJV
ŏ6HWWKHIXQFWLRQWR$&7 >21@ 
ŏ6HOHFWWKHDGMXVWPHQWNQRE6HOHFWLRQH[DPSOH 5'
ŏ7KHWULPRSHUDWLRQPRGH 0RGH &7501250 
can be selected.
CTRM mode:
0D[LPXPUDWHRIFKDQJHQHDU
FHQWHUE\FHQWHUWULPRSHUDWLRQ
NORM mode:
1RUPDOWULP KRUL]RQWDOPRYHPHQW
WULP RSHUDWLRQ7KHDGYDQWDJHRIXVLQJWKLVPRGH
LVWKDWKRYHULQJWKURWWOHFDQEHDGMXVWHGZLWKRXW
changing the curve.
ŏ7ULPDGMXVWPHQWUDQJH 5DQJH VHWWLQJ
 :KHQWKHYDOXHLVPDGHVPDOOWULPDFWVRQO\QHDU
the center.
ŏ7KHWULPUDWHFDQEHDGMXVWHGDQGWKHRSHUDWLRQ
direction can be set.
ﶬﷄﶰ ﵺ ﷎ﶪﶰﶨ﷊
ﴶﴸﴸﳜ
ﶺﶶ﷌﷊ﶼ﷤ ﶸﶶﶰﶺ﷒ﶼ
ﴶﴸﳰﴶﴸﳰﴸﴸ
Ｂ８Ｄ ﷒﷎ﶬ
ﹲ﹤﹖ﹸ﹞
ﷆﶰﶶﶪﶴ
﷎ﶬﶰﶼ Ｆ０４ Ｎ，０：
８＊＜＜ ｄｆｆﻪ
ﶰ﷒ﶬ﷊
ﻚ ﻤ
｀ｆﻪ
ﶈ ﵺ ﶄ﷦ﶊﶆ
ﶺﶶ﷌﷊
ﶰ﷒ﶸﷆ﷊
ŏ6HWVWKHGLDOXVHG