Futaba 12Z - Manual (Page 24)

24 <Basic Operation>
is displayed and the frequency data is sent to the receiver
together with a message sound. (The frequency data can be
resent by selecting [RETRY] and pushing the enter button.)
8. Turn on the receiver power while the new
frequency data above is displayed.
*When receiver frequency setting is complete, the receiver
monitor LED blinks once and the CH1 servo shuttles 3
times across the neutral position.
*The new receiver frequency data uses very low power whose
frequency is different from that of frequency channel used.
When setting the receiver frequency, bring the transmitter
and receiver as close together as possible.
*If the new data is not read correctly due to the ambient
conditions, extend the transmitter antenna and bring the
transmitter close to the receiver antenna and repeat steps 5
through 7.
*The frequency can also be changed by connecting the
transmitter and receiver directly with the DSC cord and
performing steps 5 through 8.
*When the receiver ID code is incorrect, the monitor LED
will blink. Return to the receiver ID setup screen and reset
the receiver ID.
9. When frequency setting is complete, move
the cursor to the [END] position and push the
enter button.
10.A confirmation message ("TRANSMIT?") is
displayed. To send on the new frequency,
select [YES] and push the enter button.
*To not transmit, select [NO] and push the enter button.
In case of using PCM1024, PPM receivers
*Make sure that PCM1024 or PPM is set as a modulation
scheme. Then change the frequency by the following
instruction.
How to change the frequency
7XUQRQWKHWUDQVPLWWHUSRZHU$FRQÀUPDWLRQ
message ("TRANSMIT?") is displayed. Since
you do not want to transmit, select [NO] and
then push the enter button.
2. Select [FREQUENCY] of the area that displays
the frequency on the home screen or in the
linkage menu and push the enter button.
*The frequency setup screen appears.
﷈ﶰ﷊ﶲﶪ﷊ﶸ﷎ﶢ ﴶﴸﴸﳜ
﷐﷒ﶸ﷌ ﵺ ﶸﶶﵾﶈ﷈ﶰ﷊ﶲﵾ﷎ﷄﶆﶞ ﻚ ｄＸ ﻚ ﻨＸｂﻞｄ｀ｆ：Ｄ＀ﻦ
Ｘｂ：Ｄ＀
ﶺﶶ﷌ﶪﶼ﷒ﶬﷂﶶﶸ ﵺﵺﵺﵺﵺﵺﵺ ﶞ
﷈ﶰ﷊ﶲﵾ﷐﷒ﶸ﷌ﶞﵼ ﵺ ﷒ﶰ﷊﷒ ﵺ ﶞ ＠Ｒ４Ｒ８
４Ｎ：ｄｆｂ＾
ﶺﶶ﷌﷊ﶼ﷤ ﷎ﶶﶸ﷌ﷂﶬ﷤ ﴶﴸﳰﴶﴸﳰﴸﴸ
3. When switching the frequency, select [BAND
NO.] and push the enter button.
*The frequencies which can be selected appear on the screen.
4. Select the frequency you want to use and
push the enter button.
$FRQ¿UPDWLRQPHVVDJHDSSHDUV
5. If the frequency is correct, push the enter
button.
6.A confirmation message ("TRANSMIT?") is
displayed. To send on the new frequency,
select [YES] and push the enter button.
*To not send, select [NO] and push the enter button.
Registration of the user's name
T12Z transmitter can register user's name.
How to register user's name
1. Turn on the power of the transmitter.
2. Select [USER NAME] of the area that displays
the user's name on the home screen or in the
system menu and push the enter button.
*The user name set up screen appears.
ﶪﶮ﷊ﶰ ﵺ ﶸ﷒ﶺ﷊
ﶮ﷊ﶼ﷊﷎ﶬﶞ
＊．Ｊ０ ﻚ ８Ｒ：Ｊ
ﴶﴸﴸﳜ
ＢＬ ﻚ ８＊：ＰＪ０
．ＪＮ＊０Ｊ ﻚ ：６ＬＪ
ﶺﶶ﷌﷊ﶼ﷤ ﷎ﶶﶸ﷌ﷂﶬ﷤ ﴶﴸﳰﴶﴸﳰﴸﴸ
3. Select [USER NAME] and push the enter
button. Then the set up screen will pop up.
You can use up to 12 characters as a user's
name.
ﶪﶮ﷊ﶰ ﵺ ﶸ﷒ﶺ﷊ ﴶﴸﴸﳜ
ﹶ﹘﹚ﺀﹾﺀ ︨ ﹼ﹤﹞﹢
Ｈ＊，ＲＰＲ Ｎ６０４ﻚﻚ
Ｊ８，Ｊ０
ﴌﴈﳺﴔﴊﴘ ﳌ ﴠﳼﴂﴀﴈﴂﳰ
Ｒ Ｐ Ｎ Ｌ Ｊ Ｈ Ｆ Ｄ Ｂ ＠ ＞ ＜
： ８ ６ ４ ２ ０ ． ， ＊ （ ＆ ＄
＂ ＀ ｆ ｄ ｂ ｀ ＾ ＼ Ｚ Ｘ Ｖ Ｔ
ﻜ ﻞ ﻬ ﻾ ﻤ ﻠ ﻢ
ﺘ ﺖ
ﶺﶶ﷌﷊ﶼ﷤ ﷎ﶶﶸ﷌ﷂﶬ﷤ ﴶﴸﳰﴶﴸﳰﴸﴸ
*For a description of the user's name registering: p.33.
4. Push "Return" key to return to the previous
screen after entering the user's name.
(If you want to protect the user's name)
If you don't want anybody else to change your
user's name, set your ID.
*Please be aware that you will not able to change user's name
if you forget your password.
*For a description of the user's name protection method: p.33.