Cuisinart FP-14 User Manual
Page 19
18
7.
Problem: Nub of dough forms on top of
blade and does not become uniformly
kneaded.
Solution:
r4UPQNBDIJOF
DBSFGVMMZSFNPWFEPVHI
divide it into 3 pieces and redistribute
them evenly in the work bowl.
8.
Problem: Dough feels tough after kneading.
Solution:
rDivide dough into 2 or 3 pieces and
redistribute evenly in bowl. Process 10
seconds or until uniformly soft and pliable.
9.
Problem: Dough is too dry.
Solution:
r8IJMFNBDIJOFJTSVOOJOH
BEEXBUFS
tablespoon at a time until dough cleans
the inside of the bowl.
10. Problem: Dough is too wet.
Solution:
r8IJMFNBDIJOFJTSVOOJOH
BEEGMPVS
tablespoon at a time until dough cleans
the inside of the bowl.
Technical
1. Problem: The motor does not start.
Solution:
r5IFSFJTBTBGFUZJOUFSMPDLUPQSFWFOUUIF
motor from starting if it is not properly
assembled. Make sure the work bowl
and work bowl cover are securely locked
into position.
r*GZPVBSFTMJDJOHPSTISFEEJOHBOEUIF
above solution does not work, make sure
that the food contents in the feed tube are
cut below the maximum fill line so that the
activation rod can engage the motor.
r*GUIFNPUPSTUJMMXJMMOPUTUBSU DIFDLUIF
power cord and outlet.
2. Problem: The food processor shuts off during
operation.
Solution:
r5IFDPWFSNBZIBWFCFDPNFVOMPDLFE
check to make sure it is securely in
position.
r"TBGFUZQSPUFDUPSJOUIFNPUPSQSFWFOUTUIF
motor from overheating, which is caused by
excessive strain. Press the Off control
button and wait 10 to 15 minutes to allow
the food processor to cool off before
resuming.
3. Problem: The food processor cover becomes
unlatched in the back and/or makes a loud
noise.
Solution:
r5IFCBDLPGUIFDPWFSCFDPNJOHVOMBUDIFE
and any related noise, will not prevent the
unit from working. Simply push down to
lock the back into position.
4. Problem: The motor slowed down during
operation.
Solution:
r5IJTJTOPSNBMBTTPNFIFBWJFSMPBET FH
slicing/shredding cheese) may require the
motor to work harder. Simply reposition the
food in the feed tube and try again.
r5IFNBYJNVNMPBEDBQBDJUZNBZIBWFCFFO
exceeded. Remove some of the ingredients
and continue processing.
5. Problem: It is difficult to remove the
chopping/mixing blade from the work bowl.
Solution:
r5IFTFJOOPWBUJWFCMBEFTIBWFCFFO
designed to lock in the work bowl to
prevent them from falling out when
emptying the contents of the bowl. Using
extreme care, use a little extra force to
remove the blade.
6. Problem: The food processor vibrated/
moved around the countertop during
processing.
Solution:
r.BLFTVSFUIFSVCCFSGFFUBUUIFCPUUPNPG
the unit are clean and dry. Also make sure
that the maximum load capacity is not
being exceeded.
r5IJTJTOPSNBMBTTPNFIFBWJFSMPBET FH
slicing/shredding cheese) may require the
motor to work harder.
7. Problem: The large pusher falls out when the
cover is turned upside down.
Solution:
r5IFQVTIFSMPDLGFBUVSF MPDBUFEBCPWFUIF
handle, should be pulled out.