Samson Concert 88 Camera Combo UHF Camera Wireless System (D: 542 to 566 MHz) User Manual
Page 102
102
Posizionare il trasmettitore a circa 15-30 cm (6-12") di distanza dalla parte anteriore
del ricevitore CR88 con l'apertura IR del trasmettitore di fronte al dispositivo trasmit-
tente a raggi infrarossi del ricevitore.
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and
(2) this device must accept any
interference received, including
interference that may cause
undesired operation.
FREQ:
542-566MHz
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and
(2) this device must accept any
interference received, including
interference that may cause
undesired operation.
FREQ:
542-566MHz
3. Plug in receiver
4. Turn on receiver
5. Plug receiver into audio system
6. Press Select button to change channel
9. Press and hold SELECT button to IR set
10. Adjust Volume control
7. Install batteries
8. Press button on transmitter to turn on
9. Press and hold Select button to IR set
7. Install batteries
8. Turn on belt pack transmitter
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and
(2) this device must accept any
interference received, including
interference that may cause
undesired operation.
FREQ:
542-566MHz
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and
(2) this device must accept any
interference received, including
interference that may cause
undesired operation.
FREQ:
542-566MHz
3. Plug in receiver
4. Turn on receiver
5. Plug receiver into audio system
6. Press Select button to change channel
9. Press and hold SELECT button to IR set
10. Adjust Volume control
7. Install batteries
8. Press button on transmitter to turn on
9. Press and hold Select button to IR set
7. Install batteries
8. Turn on belt pack transmitter
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and
(2) this device must accept any
interference received, including
interference that may cause
undesired operation.
FREQ:
542-566MHz
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and
(2) this device must accept any
interference received, including
interference that may cause
undesired operation.
FREQ:
542-566MHz
3. Plug in receiver
4. Turn on receiver
5. Plug receiver into audio system
6. Press Select button to change channel
9. Press and hold SELECT button to IR set
10. Adjust Volume control
7. Install batteries
8. Press button on transmitter to turn on
9. Press and hold Select button to IR set
7. Install batteries
8. Turn on belt pack transmitter
Quando la trasmissione è completa e il CR88 sta rice-
vendo il segnale RF dal trasmettitore, sul pannello
anteriore del ricevitore CR88 si accenderà la spia indi-
cante lo stato di PRONTO.
Se si riscontra che il sistema ha dei drop-out considerevoli, un ridotto range di eser-
cizio complessivo, o improvvise manifestazioni di rumore, modificare il canale su cui
il sistema funziona effettuando le operazioni sopra elencate.
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and
(2) this device must accept any
interference received, including
interference that may cause
undesired operation.
FREQ:
542-566MHz
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and
(2) this device must accept any
interference received, including
interference that may cause
undesired operation.
FREQ:
542-566MHz
3. Plug in receiver
4. Turn on receiver
5. Plug receiver into audio system
6. Press Select button to change channel
9. Press and hold SELECT button to IR set
10. Adjust Volume control
7. Install batteries
8. Press button on transmitter to turn on
9. Press and hold Select button to IR set
7. Install batteries
8. Turn on belt pack transmitter
Guida introduttiva - Configurazione di sistemi multipli
Premere e tenere premuto il tasto SELEZIONE del
CR88 per sincronizzare il trasmettitore sul medesi-
mo canale del ricevitore attraverso la trasmissione a
infrarossi.