Samson Concert 88 Camera Combo UHF Camera Wireless System (D: 542 to 566 MHz) User Manual
Page 36
36
Configuration rapide - Installation d'un seul système
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and
(2) this device must accept any
interference received, including
interference that may cause
undesired operation.
FREQ:
542-566MHz
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and
(2) this device must accept any
interference received, including
interference that may cause
undesired operation.
FREQ:
542-566MHz
3. Plug in receiver
4. Turn on receiver
5. Plug receiver into audio system
6. Press Select button to change channel
9. Press and hold SELECT button to IR set
10. Adjust Volume control
7. Install batteries
8. Press button on transmitter to turn on
9. Press and hold Select button to IR set
7. Install batteries
8. Turn on belt pack transmitter
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and
(2) this device must accept any
interference received, including
interference that may cause
undesired operation.
FREQ:
542-566MHz
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and
(2) this device must accept any
interference received, including
interference that may cause
undesired operation.
FREQ:
542-566MHz
3. Plug in receiver
4. Turn on receiver
5. Plug receiver into audio system
6. Press Select button to change channel
9. Press and hold SELECT button to IR set
10. Adjust Volume control
7. Install batteries
8. Press button on transmitter to turn on
9. Press and hold Select button to IR set
7. Install batteries
8. Turn on belt pack transmitter
Positionnez l'émetteur à environ 6 а 12" (15 а 30 cm) de la face avant du CR88, la
fenêtre infra-rouge de l'émetteur étant tournée vers l'émetteur infra-rouge situé sur la
face avant du récepteur CR88.
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and
(2) this device must accept any
interference received, including
interference that may cause
undesired operation.
FREQ:
542-566MHz
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and
(2) this device must accept any
interference received, including
interference that may cause
undesired operation.
FREQ:
542-566MHz
3. Plug in receiver
4. Turn on receiver
5. Plug receiver into audio system
6. Press Select button to change channel
9. Press and hold SELECT button to IR set
10. Adjust Volume control
7. Install batteries
8. Press button on transmitter to turn on
9. Press and hold Select button to IR set
7. Install batteries
8. Turn on belt pack transmitter
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and
(2) this device must accept any
interference received, including
interference that may cause
undesired operation.
FREQ:
542-566MHz
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and
(2) this device must accept any
interference received, including
interference that may cause
undesired operation.
FREQ:
542-566MHz
3. Plug in receiver
4. Turn on receiver
5. Plug receiver into audio system
6. Press Select button to change channel
9. Press and hold SELECT button to IR set
10. Adjust Volume control
7. Install batteries
8. Press button on transmitter to turn on
9. Press and hold Select button to IR set
7. Install batteries
8. Turn on belt pack transmitter
Maintenez le bouton SELECT du CR88 enfoncé pour
régler l'émetteur sur le même canal que le récepteur
par transmission infra-rouge.
Appuyez sur le bouton SELECT situé à l'avant du
récepteur CR88 pour choisir un canal disponible. Le
numéro du canal augmentera de un, de 0 à 9 puis de
A à F. Une fois parvenu au dernier canal, le sens de
comptage s'inversera pour revenir а 0.