Samson Concert 88 Camera Combo UHF Camera Wireless System (D: 542 to 566 MHz) - Manual (Page 78)

78
Inicio Rápido - Configuración de Sistema Simple
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FREQ: 542-566MHz
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FREQ: 542-566MHz
3. Plug in receiver 4. Turn on receiver 5. Plug receiver into audio system 6. Press Select button to change channel 9. Press and hold SELECT button to IR set 10. Adjust Volume control 7. Install batteries 8. Press button on transmitter to turn on
9. Press and hold Select button to IR set 7. Install batteries 8. Turn on belt pack transmitter
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FREQ:
542-566MHz
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FREQ: 542-566MHz
3. Plug in receiver 4. Turn on receiver 5. Plug receiver into audio system 6. Press Select button to change channel 9. Press and hold SELECT button to IR set 10. Adjust Volume control 7. Install batteries 8. Press button on transmitter to turn on
9. Press and hold Select button to IR set 7. Install batteries 8. Turn on belt pack transmitter
Coloque el transmisor a una distancia de aproximadamente 15-30 cm de la parte
frontal del CR88 con la ventana IR del transmisor orientada hacia el transmisor IR
del panel frontal del receptor CR88.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FREQ: 542-566MHz
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FREQ:
542-566MHz
3. Plug in receiver 4. Turn on receiver 5. Plug receiver into audio system 6. Press Select button to change channel 9. Press and hold SELECT button to IR set 10. Adjust Volume control 7. Install batteries 8. Press button on transmitter to turn on
9. Press and hold Select button to IR set 7. Install batteries 8. Turn on belt pack transmitter
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FREQ: 542-566MHz
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FREQ:
542-566MHz
3. Plug in receiver 4. Turn on receiver 5. Plug receiver into audio system 6. Press Select button to change channel 9. Press and hold SELECT button to IR set 10. Adjust Volume control 7. Install batteries 8. Press button on transmitter to turn on
9. Press and hold Select button to IR set 7. Install batteries 8. Turn on belt pack transmitter
Pulse y mantenga pulsado el botón SELECT del
CR88 para ajustar el transmisor en el mismo canal
que el receptor mediante transmisión infrarroja.
Pulse el botón SELECT en la parte frontal del receptor
CR88 para seleccionar un canal disponible. El número
de canal se incrementará un dígito, de 0 a 9, y des-
pués de A a F. Cuando se haya alcanzado el último
canal, el número de canal volverá a situarse en 0.