Samson Concert 88 Camera Combo UHF Camera Wireless System (D: 542 to 566 MHz) - Manual (Page 57)

57 Concert 88 Kabelloses System
ENGLISH
FR
ANÇ
AIS
DEUT
SCHE
ESP
AÑOL
IT
ALIANO
Kurzanleitung - Einstellung eines einzelnen Systems Kurzanleitung - Einstellung eines einzelnen Systems
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FREQ: 542-566MHz
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FREQ: 542-566MHz
3. Plug in receiver 4. Turn on receiver 5. Plug receiver into audio system 6. Press Select button to change channel 9. Press and hold SELECT button to IR set 10. Adjust Volume control 7. Install batteries 8. Press button on transmitter to turn on
9. Press and hold Select button to IR set 7. Install batteries 8. Turn on belt pack transmitter
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FREQ:
542-566MHz
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FREQ: 542-566MHz
3. Plug in receiver 4. Turn on receiver 5. Plug receiver into audio system 6. Press Select button to change channel 9. Press and hold SELECT button to IR set 10. Adjust Volume control 7. Install batteries 8. Press button on transmitter to turn on
9. Press and hold Select button to IR set 7. Install batteries 8. Turn on belt pack transmitter
Positionieren Sie den Sender etwa 6-12" (15-30 cm) von der Vorderseite des CR88
entfernt, wobei das IR Fenster des Senders auf den IR Sender an der Frontplatte des
CR88 Empfängers gerichtet ist.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FREQ: 542-566MHz
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FREQ:
542-566MHz
3. Plug in receiver 4. Turn on receiver 5. Plug receiver into audio system 6. Press Select button to change channel 9. Press and hold SELECT button to IR set 10. Adjust Volume control 7. Install batteries 8. Press button on transmitter to turn on
9. Press and hold Select button to IR set 7. Install batteries 8. Turn on belt pack transmitter
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FREQ: 542-566MHz
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FREQ:
542-566MHz
3. Plug in receiver 4. Turn on receiver 5. Plug receiver into audio system 6. Press Select button to change channel 9. Press and hold SELECT button to IR set 10. Adjust Volume control 7. Install batteries 8. Press button on transmitter to turn on
9. Press and hold Select button to IR set 7. Install batteries 8. Turn on belt pack transmitter
Drücken und halten Sie die CR88 SELECT Taste, um
den Sender über Infrarot Übertragung auf den glei-
chen Kanal wie den Empfänger zu stellen.
Betätigen Sie die SELECT Taste auf der Vorderseite
des CR88 Empfängers, um einen verfügbaren Kanal zu
wählen. Die Kanalnummer wird um eine Stelle erhöht,
von 0-9 AF. Sobald der letzte Kanal erreicht wurde,
wird der Zähler wieder auf 0 zurückspringen.