Honeywell VISTA-20P - Manual (Page 35)

Touch Screen Keypad (AUI) Enable
The system supports up to two touch screen style
keypads (e.g., Symphony Advanced User Interface
(AUI), and 6270 Touch Screen keypad. NOTE: Use of
touch screen devices does not affect the number of
standard keypads supported.
*189
AUI Device 1 and 2 Enable
VISTA-20P: Enter each touch screen (AUI) device’s
home partition.
0 = disabled; 1 = partition 1; 2 = partition 2; 3 = common
VISTA-15P: 0 = disabled; 1 = enabled
Set AUI 1 address to 1. Set AUI 2 address to 2.
AUI Compatibility Note: To ensure proper AUI device
operation, connect only to controls having microprocessor
version 3.0 or higher, and use AUI devices with the following
rev levels: 6270 series use version 1.0.9 or higher; 8132/8142
(Symphony) series use version 1.1.175 or higher.
Keypad Programming Fields
To enable keypads:
1. Set desired address at keypad (refer to keypad’s
instructions for setting the address).
2. Use data field program mode to enable keypad
addresses, assign a partition, enable sound options
in fields *190-*196 as shown in the table above.
3. If desired, use data field *198 to turn on the display
of the partition number.
4. Set the following keypad-related data fields as
required by the installation:
*21 Quick Arm Enable, *23 Forced Bypass, *84
Auto STAY Arm
5. If using touch screen devices (AUI), enable each
unit in field *189 and set AUI 1 to address 1, AUI 2
to address 2.
NOTE: Each keypad must be assigned a unique
address, starting at address 16 (address 16 is
reserved for keypad 1, which is automatically set to
partition 1 with all sounds enabled). Keypads
programmed with the same address will give
unpredictable results.
*190
Keypad 2 Device Address 17
Entry 1 – Partition Assignment:
0 = keypad disabled
1 = partition 1 (VISTA-20P)/keypad enabled (VISTA-15P)
2 = partition 2; 3 = common
Entry 2 – Sound Option:
0 = no suppression
1 = suppress arm/disarm and E/E/ beeps
2 = suppress chime beeps only
3 = suppress arm/disarm, E/E/ beeps and chime beeps
Entry 1: For VISTA-20P, enter the partition in which
the keypad is located; for VISTA-15P, enter 1 to
enable, or 0 to disable the keypad.
Entry 2: Enter the desired sound option for this
keypad.
*191
Keypad 3 Device Address 18
See field *190 for entries and explanation.
*192
Keypad 4 Device Address 19
See field *190 for entries and explanation.
*193
Keypad 5 Device Address 20
See field *190 for entries and explanation.
*194 Keypad 6 Device Address 21
See field *190 for entries and explanation.
*195 Keypad 7 Device Address 22
See field *190 for entries and explanation.
*196
Keypad 8 Device Address 23
See field *190 for entries and explanation.
*197
Exit Time Display Interval
0 = no display; 1-5 = seconds between display updates
If enabled, keypads display the exit time remaining
after arming the system, updated at the interval
selected (i.e. if the exit delay is 30 seconds and “2” is
selected in this field, the keypad display refreshes every
2 seconds, displaying 30, 28, 26, 24, etc.).
An interval greater than “1” may be necessary for some
older keypads to allow users time to enter key presses
between display updates.
FIXED-WORD KEYPAD NOTE: If using 2-digit
display keypads (e.g. 6150RF), do not use exit times
greater than the 96-second delay option. Using a longer
delay time may cause end-user confusion because 2-digit
display keypads cannot display times greater than “99.”
If longer exit time is required by the installation, it is
recommended that the Exit Time Display option be
disabled (“0”).
*198
Display Partition Number
VISTA-20P. 0 = no; 1 = yes
If selected, the partition number is displayed in the
upper-left corner of the display. This is useful when
using the GOTO partition function.
*199
ECP Fail Display
0 = 3-digit display (“1” + device address)
1 = 2-digit fixed-display as “91”
Select “0” if using Alpha keypads and/or 3-digit Fixed-
Word Display keypads. ECP faults will display “1” plus
the device address (00-30) of device causing the fault
(e.g., faults on device 07 display as “107”).
Select “1” if using 2-digit Fixed-Word Display keypads
(e.g., certain 6128 series keypads). If selected, ECP
faults for all devices will display as “91” on 2-digit
displays, and “191” on 3-digit or Alpha keypads.
4-11