HONDA GCV190 - Manual (Page 4)

4 ENGLISH
TYPE 4: AUTOMATIC CHOKE RETURN/FIXED THROTTLE
Starting The Engine
1. Turn the fuel valve to the ON position (see diagram, TYPE 1
Step 1 on page 2).
2. Move the choke lever to the
choke position (
E cold engine).
3. Move the flywheel brake lever
to the RUN position. The choke
lever automatically begins
moving to the OFF position
when the flywheel brake lever
is moved to the RUN position.
4. Start the engine.
Recoil Starter Types;
Pull the starter grip lightly until
resistance is felt, then pull briskly (see NOTICE, TYPE 1 Step 3 on
page 3). Begin pulling the starter grip as soon as you move the
flywheel brake lever to the RUN position and the choke starts
moving to the OFF position.
If the engine does not start before the choke moves to the OFF
position, repeat steps 2 and 3, then continue starting.
Electric Starter Types;
Turn the starter switch (located on the equipment powered by this
engine) to the START position, and hold it there until the engine
starts. When the engine starts, allow the engine switch to return to
its normal position.
NOTICE
Do not use the starter for more than 5 seconds or starter motor
damage may occur. If the engine fails to start, release the switch
and wait 10 seconds before operating the starter again.
If the engine does not start before the choke moves to the OFF
position, repeat steps 2 and 3, then continue starting.
The throttle is preset on this type.
Stopping The Engine
1. Release the flywheel brake lever to activate the flywheel brake and
stop the engine.
2. Turn the fuel valve to the OFF position (see TYPE 1 Step 1 on
page 2).
TYPE 5: MANUAL CHOKE/FIXED THROTTLE
Starting The Engine
1. Turn the fuel valve to the ON
position (see TYPE 1
Step 1 on page 2).
2. Pull the choke rod to the ON
position (cold engine).
3. Turn the engine stop switch
to the ON position.
4. Pull the starter grip lightly
until resistance is felt, then
pull briskly (see NOTICE, TYPE 1 Step 3 on page 3).
5. If the choke was used to start the engine, move the choke rod to
the OFF position as soon as the engine warms up enough to run
smoothly without use of the choke.
The engine speed is preset on this type.
Stopping The Engine
1. Move the engine switch to the OFF position.
2. Turn the fuel valve to the OFF position (see diagram, TYPE 1
Step 1 on page 2).
TYPE 6: REMOTE THROTTLE/BLADE BRAKE CLUTCH
Starting The Engine
1. Turn the fuel valve to the ON position (see TYPE 1 Step 1 on
page 2).
2. Review the instructions
provided with the
equipment powered by
this engine;
Move the choke/
throttle/stop lever to
the CHOKE position
(cold engine).
Make sure the blade
control lever is
disengaged.
3. Start the engine.
Recoil Starter Types
Pull the starter grip
lightly until resistance
is felt, then pull briskly
(see NOTICE, TYPE 1
Step 3 on page 3).
Electric Starter Types
Turn the starter switch (located on the equipment powered by this
engine) to the START position, and hold it there until the engine
starts. When the engine starts, allow the engine switch to return to
its normal position.
NOTICE
Do not use the starter for more than 5 seconds or starter motor
damage may occur. If the engine fails to start, release the switch
and wait 10 seconds before operating the starter again.
4. As soon as the engine starts, slowly move the choke/throttle/stop
lever to the FAST position.
5. Allow the engine to warm to operating temperature, then engage
the blade control lever (see equipment manual).
CHOKE
LEVER
OFF
ON
RUN
FLYWHEEL
BRAKE LEVER
STOP
ENGINE STOP SWITCH
CHOKE
ROD
ON ON
OFF
SLOW
CHOKE
CHOKE/
THROTTLE/
STOP
LEVER
FAST
STOP
POM52684-N.book Page 4 Friday, May 2, 2008 9:05 AM