Setup of the stop function at the mark point, Setting the foot switch function, Setting the stop function at the mark point – Fostex D2424 User Manual
Page 124: Flashing
124
Model D2424 Reference Manual (Changing the Initial Setting <SETUP mode>)
Flashing
1.While the recorder is stopped, press the [SETUP]
key to enter SETUP mode.
2.Turn the [JOG] dial to select “Foot SW ?” (“?”
flashes), then press the [EXECUTE/YES] key.
A flashing “
?
” will extinguish by pressing the [
EXECUTE/
YES
] key and the foot switch function information that
was lit will being flashing. Initial setting, it will show
“
Punch IO
”.
3. Select the desired function by rotating the [JOG]
dial.
4. After selecting the function, press the [EXECUTE/
YES] key again.
The selected foot switch function will be registered and
the Step-2 "
?
" will return to flashing.
5. Exit from the SETUP mode by pressing the [EXIT/
NO] key (or [STOP] button).
To cancel the operation, or to restore the setting
obtained prior to the [EXECUTE/YES] key press, press
the [STOP] button or the [EXIT/NO] key. Each time
you press one of these keys, the recorder returns to
the previous hierarchy level of the menu, and finally
exits SETUP mode and displays the previous Time Base.
Setting the foot switch function
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
SETUP
24
∞
42
OL
0
30
24
18
12
9
6
3
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
SETUP
24
∞
42
OL
0
30
24
18
12
9
6
3
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
Setup of the stop function at the mark point (“Mark Stop MD?” menu)
At the “Setup of the stop function at the mark point” menu, this sets whether or not D2424 should automati-
cally stop at the preset mark point (=locate point) during playback.
• Initial setting:
[Off]
• Option:
[OFF] or [On]
* This setting is shared by all Programs in the same disk.
* The settings cannot be saved and loaded as part of the song data.
* The settings are maintained after you turn off the power to the recorder.
Flashing
1.While the recorder is stopped, press the [SETUP]
key to enter SETUP mode.
2.Turn the [JOG] dial to select “Mark Stop MD?” (“?”
flashes), then press the [EXECUTE/YES] key.
A flashing “
?
” will extinguish by pressing the [
EXECUTE/
YES
] key and the stop function at the mark point
information that was lit will being flashing. Initial setting,
it will show “
Off
”.
3. Select "On" or "Off" with the [JOG] dial and press
the [EXECUTE/YES] key again.
The selected stop function will be registered and the
Step-2 "?" will return to flashing.
4. Exit from the SETUP mode by pressing the [EXIT/
NO] key (or the [STOP] button).
To cancel the operation, or to restore the setting
obtained prior to the [EXECUTE/YES] key press, press
the [STOP] button or the [EXIT/NO] key. Each time
you press one of these keys, the recorder returns to
the previous hierarchy level of the menu, and finally
exits SETUP mode and displays the previous Time Base.
Setting the stop function at the mark point
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
SETUP
24
∞
42
OL
0
30
24
18
12
9
6
3
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
SETUP
24
∞
42
OL
0
30
24
18
12
9
6
3
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT