Handling programs, Creating a new program, Model d2424 reference manual (handling programs) – Fostex D2424 User Manual
Page 35: Turn on the power to the recorder, Press the [pgm] key, Turn the [jog] dial clockwise, Press the [execute/yes] key, Press the [execute/yes] key again
35
Model D2424 Reference Manual (Handling Programs)
Handling Programs
This chapter explains how to handle Programs. It covers the following topics:
1. Creating a new Program
2. Using a Program Change function
3. Duplicating a Program
4. Deleting a Program
5. Editing a Program title
Creating a new Program
You can manage individual songs by setting multiple programs on the disk, as explained in the
“Managing Songs by Program Selection” section of the “Before Starting” chapter. You can set up to
99 Programs. One Program is automatically created on the disk when the disk is newly formatted
with this equipment.
Follow the steps below to create a new Program. The prerequisite of this operation is that the disk
is in an “initial state” where there is only one Program on the disk.
<Note>
• When a new program is made, the same initial setup of the currently active program will be copied as the initial
setting for the new program. If you wish to make a new program under the same settings as those of a previous
program, call up the desired program to be copied before making the new program.
• A new compilation is possible only when the "Chain Play MD?" (Setup of the chain play mode) menu in the
SETUP mode is set to "Off." If the [PGM SEL] key is pressed when the "Chain Play MD?" menu is set in other
than the "Off" mode, the D2424 will enter the "Chain play mode." Before starting compilation, check that the
"Chain Play MD?" is "Off" and if it is not, be sure to reset it to "Off."
1. Turn on the power to the recorder.
Upon starting up the recorder, “
Initialize...
”-> “
Current
IDE Drv
” -> “
Hard disk model number
”-> “
Storage mode
(“Standard format” in this case) messages are followed
with an ABS time base, then show the top of the Program
(ABS 0). At this time, the current Program is indicated
as “P01”.
2. Press the [PGM] key.
“
Select PGM!
” appears on the display briefly, then
changes to a flashing “
01
” and “
SURE?
” flash. (“******”
is the name of PGM 01.)
3. Turn the [JOG] dial clockwise.
The question marks “
?
” of “
[New Program?]
” and “
SURE?
”
flash. This indication asks you if you wish to set a new
Program (Program 2).
4. Press the [EXECUTE/YES] key.
The recorder automatically enters “
Title Edit PGM?
” menu
in SETUP mode. You can enter a title for Program 2.
(“
?
” flash.) If you prefer the default name, press the
[
EXIT/NO
] key.
5. Press the [EXECUTE/YES] key again.
A default title (#0002) appears on the display, with “
#
”
and “
SURE?
” flashing. This means that you can enter a
name for the new Program.
If you wish to name the Program with a unique title,
continue the steps below.
In either case, you can change the title later, as explained
in “
Editing a Program title
.”
Flashing
Flashing
Flashing
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
24
∞
42
OL
0
30
24
18
12
9
6
3
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
PGM
24
∞
42
OL
0
30
24
18
12
9
6
3
SURE?
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
Flashing
Flashing
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
PGM
24
∞
42
OL
0
30
24
18
12
9
6
3
SURE?
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
Flashing
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
SETUP
24
∞
42
OL
0
30
24
18
12
9
6
3
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
PGM