Marantz UD9004 - Manual (Page 32)

T
roubleshooting
Information
HDMI Control F
unction
Playback
Connections
Getting Started
Speciğcations
29
ENGLISH
Setting items Setting contents
Source Direct
Disable the speaker and
subwoofer settings and
output the disc audio as is.
NOTE
Set to within the playback
frequency band of the
ampliğer you are to use:
“On” at “50 kHz” or “100
kHz”. Setting outside the
frequency band can result
in damage to your ampliğer
and even ğre.
Off : Enable the speaker and subwoofer settings.
On : 50kHz : Output the disc contents as is. When playing Super Audio
CD, output up to 50 kHz audio signals.
On : 100kHz : Output the disc contents as is. When playing Super Audio
CD, output up to 100 kHz audio signals with DSD format.
Setting “On: 50 kHz” or “On: 100 kHz” enables full-range playback on •
all channels recommended for DTS. (Note that this results in a 5 dB
increase in subwoofer volume, and a 15 dB increase with Super Audio
CD). This also allows you to play back the 6-channel source of DVD-
Audio recorded on all channels with the full frequency range. In this
case, make an analog connection according to disc operating manual.
When set to “On: 50 kHz” or “On: 100 kHz”, all speaker sizes are set to
•
“Large” and “Yes” is set for the subwoofer.
Even when set to “On: 50 kHz” or “On: 100 kHz”, “Channel Level” and
•
“Distance” settings are available.
Compression
Compresses the dynamic
range of Dolby TrueHD/
Dolby Digital/Dolby Digital
Plus audio. At night or other
times when you cannot play
back at high volume, this
compensates by reducing
high level sounds and
increasing low level sounds. Auto : Automatically compress Dolby TrueHD audio dynamic range. The
sound is not compressed when playing signals other than Dolby TrueHD
signals.
Off : Dynamic Range compression is not applied.
Low : Set minimum dynamic range compression.
Middle : Set middle dynamic range compression.
High : Set maximum dynamic range compression.
AFDM
Automatically set the
surround mode by detecting
the surround mode
identiğcation signal recorded
in the disc. On : Automatically set surround mode when the ID signal is included.
Off : Do not set surround mode even when the ID signal is included.
MTRX : Create a surround audio signal by matrix processing, regardless
of the presence of an ID signal.
An EX Ġag may not be included for Dolby Digital EX sources. Even with
“AFDM” set to “On”, set to “MTRX” in case the playback mode does not
automatically switch.
NOTE
This setting is valid when “Audio Setup” – “7.1ch Audio Out” on the GUI •
menu is set to (vpage 32) and when “HDMI Setup” – “Audio Setup” on
the GUI menu is set to “Multi LPCM BM On” (vpage 25).
This setting is invalid when “Audio Setup” – “Source Direct” on the GUI
•
menu is set to “On” (vpage 29).
This function is invalid for the DTS-CD source.
•
Audio Setup
Setting items Setting contents
BD Effect Sound
Sets for a click sound and
other outputs during BD
popup menu operations. On : Outputs BD effect sound.
Off : Does not output BD effect sound.
BD Re-Encoder
Sets the format during
output of the BD’s Mix Audio
signal from the digital output
terminal. Auto : Outputs primary audio (main audio) in the same type of audio
format. Dolby Digital/Dolby Digital Plus/Dolby TrueHD are output as
Dolby Digital, DTS/DTS-HD are output as DTS and Linear PCM is output
as Linear PCM.
Dolby Digital : Outputs to the digital audio output terminal (optical/
coaxial) with Dolby Digital.
DTS : Outputs to the digital audio output terminal (optical/coaxial) with
DTS.
Valid when “BD Audio Mode” is set to “Mix Audio Output” (vpage
33).
Digital Out
Set the audio signal of digital
audio output.
For more information on each
audio signal, refer to “Audio
Signal from the Digital Audio
Output (Optical/Coaxial)
Terminal” (vpage 17). Bitstream : Outputs a bitstream signal. Converts Dolby TrueHD, Dolby
Digital Plus to Dolby Digital, and DTS-HD to DTS for output.
PCM : Output the downmixed audio signal to 2ch LPCM.
PCM Down Sampling : Convert sampling frequency audio greater than
48 kHz to a 48 kHz 2ch LPCM audio output signal.
When outputting CD, etc. to a digital recording device such as the CD •
recorder, convert to PCM or PCM down sampling.
When a disc with recorded Linear PCM or PPCM (Packed PCM) is played
•
back, this outputs Linear PCM irrespective of the setting.
Downmix
Set the method used to
convert a multi-channel
audio signal to a 2-channel
signal. Lt/Rt : Signals are converted to Dolby Surround compatible 2-channel
audio signals for output. This setting is valid for DTS-HD, DTS Digital
Surround, Dolby Digital Plus and Dolby Digital audio signals. (If the
connected AV Amp is Dolby Pro Logic compatible, AV Amp plays back
using surround audio.)
Stereo : Outputs by converting to the 2ch (stereo) audio.
NOTE
In order to enable the “Lt/Rt” setting when playing back BD, set “BD
Audio Mode” to “HD Audio Output” (vpage 33).
Setup
Remote control operation
buttons
SET UP :
Displaying the menu
Cancel the menu
d f 0 1 :
Moves the cursor
(Up/Down/Left/Right)
ENTER :Decision the setting RETURN :Return to previous menu