Marantz UD9004 - Manual (Page 38)

35
T
roubleshooting
Information
HDMI Control F
unction
Playback
Setup
Connections
Getting Started
Speciğcations
ENGLISH
Setup
Setting items
Setting
contents
Default
DNR
Reduce noise in the entire
picture.
0 ~ +3 0
Contrast
Adjust picture contrast.
–6 ~ +6 0
Brightness
Adjust picture brightness.
0 ~ +12 0
Enhancer
Strengthens the contours of
the picture.
0 ~ +11 0
Gamma Correction
Adjust video brightness in
detail.
G0 ~ 9
G0 = 24 / G1 = 32
G2 = 48 / G3 = 64
G4 = 80 / G5 = 96
G6 = 128 / G7 = 160
G8 = 192 / G9 = 224
Sharpness (medium range)
z1
Adjust picture sharpness
for the medium frequency
range.
–6 ~ +6 0
Sharpness (high range)
Adjust picture sharpness for
the higher frequency range.
–6 ~ +6 0
Hue (color tone)
Adjust the green and red
color balance.
–6 ~ +6 0
White Level
Adjust the white level.
–5 ~ +5 0
Black Level
Adjust the black level.
–5 ~ +5 0
Chroma Level
Adjust the color density.
–6 ~ +6 0
Setup Levelz2
Adjust the black areas of the
image.
0 IRE
7.5 IRE
7.5 IRE
H.Position
Adjust the left/right position.
–7 ~ +7 0
V.Position
Adjust the top/bottom
position.
–7 ~ +7 0
z1 : This is not available for HDMI output.
z2 : Effective only for the 480i video signal from the video output terminal, S
video output terminal, and component video output terminal.
You can adjust the picture quality to your liking.
You can store up to a maximum of 5 values in memory.
When Finishing Picture Adjustment n
Press PICT. ADJUST button during picture
adjustment.
When Outputting Standard Picture n
Quality without Using Picture
Adjustment
Press RETURN and d, f buttons to select
“Standard” and then press ENTER button.
About Gamma Correction
When you select “Gamma Correction”, and then press ENTER button,
you can change the setting with d, f, 0, 1 buttons.
In the example of the graph below, the horizontal axis shows the
brightness level of the pictured recorded on the disc. The vertical axis
shows the brightness of the picture output by the UD9004.
Gamma Correction Memory 5
0
0
255
255
G0:024
On adjusting the brightness on the output side of bright parts on •
the disc side, the normally hard to see bright parts become clearly
discernible images.
Gamma Correction Memory 5
0
0
255
255
G0:024
On adjusting the brightness on the output side of dark parts on •
the disc side, the normally hard to see dark parts become clearly
discernible images.
Resuming Initial Values after Gamma Correction n
Press CLEAR button while a graph is displayed.
The picture adjustment set values are retained in
memory even after the power is turned off.
Adjusting the Picture Quality (Picture Control)
1
Press PICT. ADJUST button.
The currently set status is displayed.
2
Select the memory number you want (“Memory 1”
~ “Memory 5”) with d, f buttons, and then press
ENTER button.
Standard
Memory 1
Memory 5 PICT
3
Select the item you want to change
with d, f buttons.
Memory 1
DNR
Contrast
V.Position
0
0
0
4
Change the setting with 0, 1
buttons.
Refer to the table on the right regarding contents of items which b
can be set.