Sony 3-270-589-12 (1) - Manual (Page 104)

104
System Menu
Cha
p
te
r 6
Me
nu
s
ESSENCE MARK [>
EssnceMk] SDI OUT [>> SDI out]: Select
whether to output
essence marks in the
VANC of HD/SDSDI
output.
* ON [>>> ON]: Output.
OFF [>>> OFF]: Do not output.
SD VANC LINE [>> SDI
line]: When SDI OUT is
set to “ON”, select the
line of SDSDI output in
which to output essence
marks.
12LINE [>>> 12 line] to 19LINE [>>> 19 line]: Select in the
range line 12 to line 19.
Factory default setting: *17LINE (line 17)
HD VANC LINE [>> HD line]:
When SDI OUT is set to
“ON”, select the line of
HDSDI output in which to
output essence marks.
9LINE [>>> 9 line] to 20LINE [>>> 20 line]: Select in the
range line 9 to line 20.
Factory default setting:*17LINE (line 17)
HD VANC INPUT [> HD
VANC IN]: Make settings
related to recording of the
VANC data contained in
HDSDI input.
LINE [>> Line]: Select the
line whose VANC you
want to record
* OFF [>>> OFF]: Do not record VANC from any line.
9LINE [>>> 9 LINE] to 20LINE [>>> 20 line]: Select from the
range line 1 to line 20.
Note
When this item is set to any setting other than OFF, VANC
packet information is saved in the DATA ITEM section of MXF
files.
DID [>> DID]: Select the DID
of the VANC you want to
record.
00 [>>> 00] to FF [>>> FF]
Factory default setting: *00 [>>> 00]
SDID [>> SDID]: Select the
SDID in the VANC you
want to record
00 [>>> 00] to FF [>>> FF]
Factory default setting: *00 [>>> 00]
DATA ITEM OUT [> DATA ITEM]: Specify whether to include
the information from recorded VANC packets in data items
in the DATA ITEM section of MXF files.
OFF [>> OFF]: Do not include VANC packet information in
data items.
* ON [>> ON]: Include VANC packet information in data items.
Note
Set this menu item to OFF when you connect a nonlinear
editing system that does not support DATA ITEM.
SETUP BANK OPERATION [Setup Bank]: Settings related
to menu bank operations Description
Menu bank: This unit allows three different complete sets of menu settings to be saved in what are termed “menu banks”
numbered 1 to 3.
RECALL BANK 1 [> Recall 1]: Recall menu settings from
menu bank 1.
Operate with the following procedure.
(1) Select the bank you want to recall, then press the
,/OUT
button.
Message “RECALL OK?” appears.
(2) To recall, press the SET button.
To quit recalling, press the RESET button.
(3) To save the recalled bank, press the SET button once
again.
RECALL BANK 2 [> Recall 2] :Recall menu settings from
menu bank 2
RECALL BANK 3 [> Recall 3]: Recall menu settings from
menu bank 3.
SAVE BANK 1 [> Save 1]: Save current menu settings to
menu bank 1.
Operate with the following procedure.
(1) Select the bank you want to save, then press the
,/OUT
button.
Message “SAVE OK?” appears.
(2) To save, press the SET button.
To quit saving, press the RESET button.
SAVE BANK 2 [> Save 2]: Save current menu settings to
menu bank 2.
SAVE BANK 3 [> Save 3]: Save current menu settings to
menu bank 3.
METADATA [Metadata]: Metadata settings Description