Sony 3-270-589-12 (1) - Manual (Page 30)

30
Connections and Settings
Chap
te
r 2
Pr
epa
ra
tio
n
s
• This unit’s S400 connector has 6 pins. Check the
number of pins on the i.LINK connector of your
notebook computer, and use an appropriate i.LINK
cable.
See “Using PDZ-1 Proxy Browsing Software” in Chapter
4 (page 79) for more information about installing the
PDZ-1 software. See the online help of PDZ-1 for more
information about using PDZ-1.
Some limitations apply to FAM connections. For details,
see “File Operations in File Access Mode (for Windows)”
in Chapter 5 (page 83).
Connecting to a Nonlinear Editing
System (AV/C Connection)
You can send video/audio signals (AV/C data) from this
unit to a nonlinear editing system connected to the S400
connector.
The following figure shows an example connection.
See “Using PDZ-1 over an i.LINK Connection (FAM
Connection)” (page 29) for the connections and settings to
make a FAM connection between this unit and a nonlinear
editing system.
• The S400 connector of this unit outputs video/audio
signals in DVCAM format. Data recorded in MPEG HD
format is output after being converted into DVCAM
format.
• The nonlinear editing system to be connected to this unit
requires editing software (not supplied) supporting the
DVCAM format.
• To transfer video and audio signals (AV/C data), use
AUDIO CONTROL >DV OUT MODE (see page 102)
in the setup menu to select the audio mode (the factory
default is “2ch”).
• This unit’s S400 connector has 6 pins. Check the
number of pins on the i.LINK connector of your laptop
computer, and use an appropriate i.LINK cable.
Connections for Cut Editing
By connecting this unit to a VTR, you can configure a cut
editing system. Some example connections are shown in
the following.
This unit cannot be used as a recorder for linear editing.
When it receives an assemble command, this unit starts
normal recording operation and creates a new clip.
On the computer On this unit
Install PDZ-1. Set the setup menu item
INTERFACE SELECT
>REMOTE I/F to “i.LINK”
(see
page 103).
Set the setup menu item
INTERFACE SELECT >i.LINK
MODE to “FAM(PC REMOTE)”
(see page 103).
SDSDI OUTPUT HDSDI INPUT
AUDIO INPUT
HDSDI OUTPUT
1 2
REF VIDEO INPUT TIME CODE
POWER
ANALOG HD INPUT
DIGITAL
AUDIO
(AES/EBU)
COMPOSITE OUTPUT AUDIO MONITOR
1/3 2/4
AUDIO OUTPUT
1/3 2/4
R L IN OUT
Y/G P B /R
SYNS
RS232C REMOTE(9P)
P B /B
1/2
INPUT
OUTPUT
CONTROL
3/4
1/2 3/4
S400
MONITOR
- AC IN
S400
PDW-F75 (this unit)
i.LINK cable
(not supplied)
i.LINK (IEEE1394) connector
Laptop computer
Notes
On the computer On this unit
Install editing software
supporting the DVCAM
format. Set the setup menu item
INTERFACE SELECT
>REMOTE I/F to “i.LINK”
(see
page 103).
Set the setup menu item
INTERFACE SELECT >i.LINK
MODE to “AV/C”
(see page
103).
Note
SDSDI OUTPUT HDSDI INPUT
AUDIO INPUT
HDSDI OUTPUT 1 2
REF VIDEO INPUT TIME CODE
POWER
ANALOG HD INPUT
DIGITAL
AUDIO
(AES/EBU)
COMPOSITE OUTPUT AUDIO MONITOR
1/3 2/4
AUDIO OUTPUT
1/3 2/4
R L IN OUT
Y/G P B /R
SYNS
RS232C REMOTE(9P)
P B /B
1/2
INPUT
OUTPUT
CONTROL
3/4
1/2 3/4
S400
MONITOR
- AC IN
S400
Laptop computer
i.LINK (IEEE1394) connector
i.LINK cable
(not supplied)
PDW-F75(this unit)