Sherwood R-963 - Manual (Page 34)

ENGLISH
34
ROOM 2 SOURCE PLAYBACK
This function allows enjoying one source in the main room and playing another in a different room at the same time.
The analog signals from the 7.1 CH DIRECT inputs and TAPE MONITOR INs as well as the digital signals from the coaxial or
optical digital input cannot be output from the ROOM 2 OUTs, meaning no playback in a different room.
When you connect the multi - room adapter to the MULTI - ROOM jack of this unit, you can control this unit with not only the
universal remote control unit but also the ROOM 2 remote control unit in a different room, too.(For details, refer to
“CONNECTING MULTI - ROOM SYSTEM KIT” on page 8 and “ROOM 2 Remote Controls” on page 17.)
When using the ROOM 2 remote control unit
You can use the ROOM 2 function with the ROOM 2
remote control unit more conveniently.
Press the ROOM 2 button.
1
When using the universal remote control unit or the
buttons on the front panel.
Press the ROOM 2 button.
1
Select the desired
input as a ROOM 2
source.
2
“R2” is flickering for 3 seconds and the
ROOM 2 function is activated.
To cancel the ROOM 2 function, press it again.
Then “R2” goes off.
In the operating mode, when one of the ROOM 2 INPUT
SELECTOR buttons on this remote control is pressed, the
ROOM 2 function is automatically activated without pressing
the ROOM 2 button and the desired input is selected.
The selected ROOM 2 source is displayed for 3 seconds as
follows: (R2) PHONO, (R2) TUNER, (R2) CD, (R2) AUX,
(R2) VIDEO 1~5.
Only these sources can be played in another room.
When an audio program source is selected as a ROOM 2
source, the image of the video program source selected
previously can be played separately, too.(For details, refer to
“SETTING THE ROOM2 FEED SETUP” on page 50.)
The MUTE and VOLUME UP/DOWN(
) buttons on this
remote control can be available for the ROOM 2 source only.
Note:
When the muting effect for the ROOM 2 source is operating,
“R2” is flickering.
Start play on the component related to the
ROOM 2 source.
3
Select the desired input as a ROOM 2 source
while “R2” is flickering.
2
“R2” flickers for 3 seconds and the ROOM 2 function is
activated.
To cancel the ROOM 2 function, press the button.
Then “R2” goes off.
You can cancel the ROOM 2 function with using these
buttons even in the standby mode.
The selected ROOM 2 source is displayed for 3 seconds.
Only while “R2” is flickering, the volume level for the
ROOM 2 source can be adjusted.
When “R2” is not flickering and lights up, press the ROOM
2 button briefly twice.
Start play on the component related to the
ROOM 2 source.
3
Notes:
Even when this unit enters the standby mode, in such a case that “R2” lights up still and the STANDBY button lights up in blue
as it does in the operating mode, meaning only the ROOM 2 circuitry operates, the ROOM 2 source can be played independently.
When the ROOM 2 function is operating in the standby mode, only the ROOM 2 remote control unit is available.
When you do not use the ROOM 2 function, cancel the ROOM 2 function to save electricity.
For ROOM 2 volume adjustment, refer to “ SETTING THE ROOM 2 FEED SETUP” on page 50.
ROOM2 FEED
or
OFF
OSD POWER
MAIN PAGE FAV
MUTE
CH/ SET
VOL
RETURN
DISC DISP
MI
ROOM 2
1 STEREO
7.1 SURR
CH
2 3
4 5 6
7 8 9
0 ENT
M2 M3
AUTO DSP
RNC-500
ROOM 2
ENT
POWER
OFF
OSD
or
AUDIO VIDEO
ROOM2
PHONO CD
AUX AUDIO
TUNER
VIDEO 1 VIDEO 2
VIDEO 4 VIDEO 5
MUTING
VOLUME
VIDEO
VIDEO 3
ROOM2
ROOM2
PHOTO CD
AUX AUDIO
TUNER
VIDEO 1 VIDEO 2
VIDEO 4 VIDEO 5
MUTING
VOLUME
VIDEO
VIDEO 3
PHONO CD
AUX
AUDIO
TUNER
VIDEO 1 VIDEO 2
VIDEO 4 VIDEO 5
VIDEO
VIDEO 3