Sony HDW-S280 - Manual (Page 63)

63
Items in the Basic Setup Menu
C
h
a
p
te
r 9
S
e
tu
p M
e
nus
9-3 Items in the Basic Setup Menu
The basic setup menu contains the following items.
In the Settings column of the table, the factory setting is
indicated by enclosing parenthesis.
Item
number Item name Settings
001 PREROLL TIME 0S~[5S]~30S: Set the preroll time to between 0 and 30 seconds.
A preroll time of at least 5 seconds is recommended when using this unit for editing.
002
a) CHARACTER
H-POSITION Adjust the horizontal screen position of the character information output from the
COMPOSITE OUT 2 (SUPER) connector, HD SDI OUTPUT (SUPER) connectors, and
SDI OUT 2 (SUPER) connector for superimposed display on the monitor.
00~[1E]~3C (59.94i, 29.97PsF mode)/00~[1B]~36 (50i, 25PsF, 24PsF, 23.98PsF
mode): The hexadecimal value 00 is for the far left of the screen and increasing the
value moves the position of the characters to the right.
003
a) CHARACTER
V-POSITION Adjust the vertical screen position of the first line of the character information output
from the COMPOSITE OUT 2 (SUPER) connector, HD SDI OUTPUT (SUPER)
connectors, and SDI OUT 2 (SUPER) connector for superimposed display on the
monitor.
00~[59]~73 (59.94i, 29.97PsF mode)/00~[70]~8A (50i, 25PsF, 24PsF, 23.98PsF
mode): The hexadecimal value 00 is for the top of the screen and increasing the
value lowers the position of the characters.
Note
When displaying timecode, there is a slight time delay. Therefore, when creating a tape
for off-line editing, the information inserted in the upper half of the screen may be
delayed by one frame.
004 SYNCHRONIZE When editing using this unit as a controller and an external VTR connected to this unit
via a 9-pin remote control cable, this item determines whether or not to operate the two
units in phase synchronization.
OFF: Do not operate in phase synchronization.
[ON]: Operate in phase synchronization.
005 DISPLAY INFORMATION
SELECT Determines the kind of character information to be output from the COMPOSITE OUT 2
(SUPER) connector, HD SDI OUTPUT (SUPER) connectors, and SDI OUT 2 (SUPER)
connector when CHARACTR on the HOME page of the function menu is set to ON.
[T&STA]: Time data display information and the status of the unit
T&UB: Time data display information and the user bit
T&CTL: Time data display information and CTL
T&T: Time data display information and timecode (LTC or VITC)
TIME: Time data display information only
If there is an overlap between the setting for this item and the setting for the front panel,
it is automatically avoided. For example, if CTL is selected on the front panel and this
menu item setting is T&CTL, then CTL and LTC are output.
006 LOCAL FUNCTION
ENABLE Determines which buttons on the front panel are enabled when this unit is controlled
from external equipment.
DIS: All buttons and switches other than DISPLAY and PAGE buttons are disabled.
[S&E&F]: Only the STOP button, EJECT button, and function buttons are enabled.
ENA: All buttons and switches are enabled.
007 TAPE TIMER DISPLAY Determines whether to display the CTL count in 12-hour mode or 24-hour mode.
[+-12H]: 12-hour mode
24H: 24-hour mode
008 MONITORING
SELECTION FOR
VTR-TO-VTR EDIT For recorder-player editing with only one monitor connected to the recorder, determines
whether the recorder is forced into E-E mode when R/P on the P5 EDIT page of the
function menu is set to PLAYER to view the player’s playback signals on the monitor.
[MANU]: Do not force the recorder into E-E mode.
AUTO: Force the recorder into E-E mode.