Sony XT-V70 - Manual

1 2 3 4
5 6 7
8 9 0 qa
1
Precautions
•This unit is designed for negative ground 12 V DC systems only.
•Do not get the wires under a screw, or caught in moving parts
(e.g. seat railing).
•Before making connections, turn the car ignition off to avoid
short circuits.
•Connect the red power input leads only after all other leads have
been connected.
•Run all ground wires to a common ground point.
Fuse replacement
When replacing the fuse, be sure to use one matching the
amperage rating stated on the original fuse. If the fuse blows,
check the power connection and replace the fuse. If the fuse blows
again after replacement, there may be an internal malfunction. In
such a case, consult your nearest Sony dealer.
Fuse (0.5 A)
TV aerial amplifier unit 4
Parts list (1)
•The numbers in the list are keyed to those in the instructions.
• Use 9 and 0 to organize cords.
Connection example (2)
Connection diagram (3)
Installing the TV tuner unit (4)
Notes
• Ensure that the mounting surface is clean.
• Do not install the TV tuner unit
– in locations subject to high temperatures.
– in locations subject to direct sunlight, warm air from heater
outlets, or other locations that can get hot.
• When attaching the hook-and-loop fastener to the bottom of the TV
tuner unit, do not cover the model name plate in the center.
Keep the units and connection cables apart.
The AV Center main unit, the monitor, TV tuner unit, and RCA
interconnects should not be in close proximity. Otherwise noise
interference may affect the TV picture.
Mounting the TV aerial
Mount the film aerial 5 to the car and connect the TV tuner unit.
For directions on connecting the TV tuner unit, see also
“Connection diagram (3)”.
Before mounting
•It may not be possible to mount the aerial on some cars.
- In cars with glass that does not transmit radio waves (infrared
reflecting glass, insulated glass, glass that is opaque to
electromagnetic waves, etc.), the signal reception will be
extremely poor.
- The aerial cannot be mounted in cars which have airbags in the
front pillars.
•Mount the aerial to the front window, in the specified location
and according to the specified dimensions.
- The supplied film aerial is designed for attaching only to the
front window. If attached to the rear window or elsewhere in
the car, the signal reception may be extremely poor.
Notes
• Once you have mounted the film aerial, do not attempt to remove it
and attach it again, as the adhesive will be considerably weakened.
Be sure to temporarily fasten the cable and aerial in place and check
that the cable has sufficient play before permanently attaching.
• During the mounting procedure, it will be necessary to remove the
front pillar molding to attach a ground wire.
When performing the installation yourself, if you decide it is too
difficult to remove the front pillar molding, please contact your
dealer for assistance. (Note that your dealer may charge a fee for
their assistance.)
Required items
Have the following items handy before beginning the mounting
procedure.
•Tools (Philips screwdriver, etc.)
•Cellophane tape
•Scissors
•Spray bottle (fill with 500 ml water and one or two drops of
detergent)
•Paper towels
Note
Mount the film aerials to the inside of the front window. Do not mount
the aerials anywhere other than the location described here.
Before attaching
Using the supplied cleaning cloth qa to wipe away any oil, wax, or dust
tat may be on the window.
Mounting position (5)
Installation complete
Film aerial mounting procedure
Check the film aerial 5 mounting position (6)
1 Align the film aerial power supply point with the lower edge
of the window’s ceramic line and fasten temporarily in place
with cellophane tape (6-1).
Do not remove the adhesive backing from the aerial yet.
The figure shows the results of this step, for the left aerial.
Temporarily position the right aerial in the same manner.
2 Mark the left and right sides of the film aerial, using
cellophane tape, etc (6-2).
Remove the inner molding from the front pillars on
both sides of the front window (7)
The figure shows an example of a car, such as a sedan or SUV,
which as a handle mounted on the front pillar.
Notes
• The molding on the front pillar will be fastened in place with clips or
screws. When removing it, take care not to damage or deform it.
• When performing the installation yourself, if you decide it is too
difficult to remove the front pillar molding, please contact your
dealer for assistance. (Note that your dealer may charge a fee for
their assistance.)
XT-V70
© 2005 Sony Corporation Printed in Japan
×2
3
5.3 m 5 m Ч2
Ч2
Ч4
AUX 3
CONTROL OUT
VIDEO OUT
AUX 3
VIDEO OUT
VIDEO IN
ANT IN
CONTROL OUT
2
5
6
1 2
4
7
8
1
2
4
3
Attach film aerial 5 (8)
Before attaching
• Remove the film aerial, which you previously fastened temporarily in
place, before beginning these steps.
• Cover the dashboard with a cloth to protect it from the water and
detergent.
• Clean the front window well to remove any dirt, oil, or anti-fogging
agent before beginning these steps.
1 Using a spray bottle, wet the inside of the front window well
with a mild detergent solution. The optimal solution is 500 ml
of water with one or two drops of detergent (8-1). (Pure
water will not work well for making fine adjustments.)
2 Remove the clear backing from the film aerial. Using the spray
bottle, wet the exposed surface well with the mild detergent
solution (8-2).
•Grasp the peel-off tab and peel the clear backing off slowly.
•Do not remove the protective sheet from the other side (the
side that faces the inside of the car) yet. You will remove that
sheet in step 8-4.
•Take care not to get dirt or fingerprints on the exposed
surface of the film aerial.
When attaching the film aerial
• Position the aerial vertically by aligning the upper edge of the
aerial with the lower edge of the ceramic line. Position it
horizontally by aligning the edges with the marking (cellophane
tape, etc.) that you previously placed on the window.
• Do not let the front window get dry as you are working. Spray it
again with the detergent solution as needed.
• Until the front window dries, you can slide the aerial to adjust its
position.
• When you have the aerial positioned where you want it, remove
the markings.
3 Stick the film aerial to the front window (8-3).
4 Use the supplied squeegee 8 to make sure the film aerial is
well attached to the window (8-4).
•Hold the aerial so it does not move while using the squeegee.
•Work from the center of the aerial outward.
•Work the squeegee along the length of the aerial, pushing out
air bubbles to obtain a good seal.
•Do not rub the aerial too hard.
Note
Make sure that the film aerial is completely dry before continuing
with the mounting procedure. Continuing before the aerial is dry
may cause it to come off the window.
5 Use paper towels to wipe away the excess detergent solution
and dry the aerial well.
We recommend you let the aerial dry for 3-4 hours.
Do not try to rush the drying process by using a hair dryer or
other heater. Doing so may damage the film aerial.
Turn over. t
×6
Installation/Connections
ڔᓤ0ೌ୻
Notice to dealers and installers
Please return this manual to the customer after the installation is completed.
༿ளሾ࿜ਜ਼ڔᓤᑗᓖፀ
ڔᓤஉၦઁ༿୓ࠥ၄ݿऩથ৊ఱઓă
Mobile TV Tuner
໱ޱ࢟၁ࢯቕ໭
2-597-470-32(1)
2RR6P12A23400A
AV Center
BWᒦቦ
XAV-A1
TV tuner unit
࢟၁ࢯቕ໭
XT-V70
AV Center
BWᒦቦ
XAV-A1 Film aerial 5
5 ۡෞᄖሣ5
RCA interconnects (5 m) 2
2 SDBୣઑೌ୻ሣ)6n*2
TV aerial amplifier
unit 4
4 ࢟၁ᄖሣहࡍ໭4
Aerial input cable 6
6 ᄖሣၒྜྷ࢟಄6
TV tuner unit
࢟၁ࢯቕ໭
XT-V70
Black
੨ྻ
Bus cable (5.3 m) 1
1 ᔐሣ࢟಄)6/4n*1
To a metal surface of the car
ೌ୻ࡵ໱ޱࡼ஘ၢܭෂ
Red
੺ྻ
To the +12 V power terminal
which is energized in the accessory
position of the ignition key switch.
Be sure to connect the black
ground lead to it first.
ೌ୻Ᏼ࢛૜Ꮩߓఎਈࡼএୈᆡᒙดଝ
࢟ኹࡼ,23W࢟Ꮞ࣡ᔇă
༿ᇗܘሌೌ୻੨ྻ୻࢐ሣă
Fuse(0.5A)
ۣሙႋ)1/6B*
Hook-and-loop fastener 3
3 ৣણࡈి3
On installation surface
ڔᓤܭෂ
Hook-and-loop fastener 3
3 ৣણࡈి3
XT-70V
Front pillar
༄ᑽᓏ
Aerial input cable 6
6 ᄖሣၒྜྷ࢟಄6
Film aerial (left) 5
5 ۡෞᄖሣ)ᔧ*5
Film aerial (right) 5
5 ۡෞᄖሣ)ᎎ*5
TV aerial amplifier unit 4
4 ࢟၁ᄖሣहࡍ໭4
Aerial input cable 6
6 ᄖሣၒྜྷ࢟಄6
Front pillar
༄ᑽᓏ
Power supply point
࢟Ꮞ࢛
Ceramic line
ჿࠣሣ
Align the upper edge of the
aerial with this line.
ڳᄖሣࡼ࿟ܟዘ࣪ᓰᑚᄟሣă
Temporary fastener
(cellophane tape, etc.)
೹ဟৼࢾୈ)ᅀීୢࢀ*
Marking (cellophane tape, etc.)
ܪ଑)ᅀීୢࢀ*
Front pillar
༄ᑽᓏ
Spray bottle
๿ᇓີ
Marking (cellophane tape, etc.)
ܪ଑)ᅀීୢࢀ*
Peel-off tab
۠ಭຢ
Align the upper edge of the aerial with this line.
ڳᄖሣࡼ࿟ܟዘ࣪ᓰᑚᄟሣă
Marking (cellophane tape, etc.)
ܪ଑)ᅀීୢࢀ*
Squeegee 8
8 ሴບਦᒷ8
•
•
•
•
•
4
1
•
•
9 0
2
3
4
•
•
–
–
•
5 3
•
-
-
•
-
•
•
•
•
•
•
•
qa
5
5 6
1
6-1
2 6-2
7
•
•
5 8
•
•
•
1
8-1
2
8-2
•
•
8-4
•
•
•
•
•
3 8-3
4 8
8-4
•
•
•
•
5
ᓖፀူሲ
•۾࿸۸ஞး፿᎖ঌ૵୻࢐23WEDᇹᄻă
•༤ᇖ୓ࡴሣᒙ᎖൛ႋሆLj૞ۻ૚ࣅݝୈఌᓕDŽྙᔭጬਜࡸDžă
•Ᏼ஠ቲೌ୻ᒄ༄Lj༿୓໱ޱᇬ૜Ljጲ඾࣢വă
•ᒑᎌᏴჅᎌ໚჈ࡴሣ࣒ጯೌ୻ᒄઁLjݣถೌ୻લྻਜ਼੺ྻ࢟Ꮞ
ሣă
•୓Ⴥᎌ୻࢐ࡴሣ୻ᒗጙৈৢᄴࡼ୻࢐࢛ă
ৎધۣሙႋ
ࡩৎધۣሙႋဟLjܘኍဧ፿९੝Ꮗۣሙႋ࿟Ⴥਖࢾڔ๸ऄࢾᒋࡼۣ
ሙႋăྙਫۣሙႋ࿥ࣥLj༿ଶއ࢟Ꮞሣവೌ୻݀ৎધۣሙႋăྙਫ
ৎધઁۣሙႋᏳࠨ࿥ࣥLjᐌభถဵดݝ৺ᑇăࠥဟLj༿Ꭷ௦ิᔢத
ࡼTpozሾ၉࿜ೊᇹă
ۣሙႋ)1/6B*
࢟၁ᄖሣहࡍ໭4
ݝୈ༹࡝)1*
•༹࡝ᒦࡼܠ੓Ꭷဧ፿ႁීၗᒦࡼܠ੓ጙᒘă
•ဧ፿9ਜ਼0ᎌኔܠᔝ࢟ሣă
ೌ୻௟ಿ)2*
ೌ୻ᅄ)3*
ڔᓤ࢟၁ࢯቕ໭)4*
ᓖፀ
•
ཀྵۣڔᓤܭෂ༹ஈă
• ༤ᇖ୓࢟၁ࢯቕ໭ڔᓤ
–
Ᏼߌ၊঱ᆨࡼᆡᒙă
– Ᏼߌ၊ᒇ࿴ዴ਒Ăଝེ໭๝߲ࡼེ໮૞໚჈ถࡴᒘܤེࡼᆡᒙă
• ࡩ୓ৣણࡈిᐫᄣᒗ࢟၁ࢯቕ໭ࡼ࢏ݝဟLj༤ᇖ୓ᒦମࡼቯ੓ූ๞঄ঙ
ࢬă
ဧࢯቕ໭Ꭷೌ୻࢟಄ۣߒॊಭă
BWᒦቦᓍ૦Ăመာ໭Ă࢟၁ࢯቕ໭ਜ਼SDBୣઑೌ୻ሣݙభጲ੪୻தă॥
ᐌLjᐅፒছཷభถ્፬ሰ࢟၁ઙෂă
ڔᓤ࢟၁ᄖሣ
ڳۡෞᄖሣ5ڔᓤࡵ໱ޱ࿟݀ೌ୻࢟၁ᓍ૦ă
ᎌਈೌ୻࢟၁ᓍ૦ࡼऱሶLj༿ݬᏞĐೌ୻ᅄDŽ3Džđă
ڔᓤᒄ༄
•ᎌቋ໱ޱభถᇄजڔᓤᄖሣă
- Ᏼᓤᎌݙถࠅၒᇄሣ݆࢟ࡼ݁ೇDŽ੺ᅪሣन࿴݁ೇĂ௾Ꮟ݁
ೇĂݙถᅀਭ݆࢟ࠟࡼ݁ೇࢀDžࡼ໱ޱดLjቧ੓ࡼ୻၃ऻޟ
ތă
- ᄖሣݙถڔᓤᏴ༄ᑽᓏᓤᎌڔཝ໮ฌࡼ໱ޱ࿟ă
•ো௣ਖࢾࡼߛࡁڳᄖሣڔᓤࡵ༄ࠊࡼਖࢾᆡᒙă
- Ⴒ૦ᄋ৙ࡼۡෞᄖሣஞ፿᎖ڔᓤࡵ༄ࠊ࿟ăྙਫڔᓤࡵઁࠊ૞
ޱดࡼ໚Ⴧ࢐ऱLjቧ੓ࡼ୻၃ऻޟތă
ᓖፀ
•
ጙࡡڔᓤੑۡෞᄖሣઁLj௓ݙገ၂ᅄގሆਜ਼ᒮቤڔᓤLjፐᆐᑚዹ્ဧᐫቶ
ܤࡻሤࡩތă༿ᇗܘᏴ፼௉ڔᓤ༄ሌ᏷ဟڳ࢟಄ਜ਼ᄖሣৼࢾࡵᆡ݀ଶއ࢟
಄ဵ॥ᎌߠॊࡼ᎜೟ă
• Ᏼڔᓤਭ߈ᒦLjభถኊገގሆ༄ᑽᓏኹᄟጲڔᓤ୻࢐ሣă
ิᔈ଄஠ቲڔᓤဟLjྙਫิ௻ࡻ༄ᑽᓏኹᄟ੪ซގሆLj༿ೊᇹளሾ࿜ኰཇ
ۑᓐăDŽ༿ᓖፀิࡼளሾ࿜భถ્࣪ᑚࠨۑᓐ஠ቲ၃ॅăDž
ኊገᇕອ
Ᏼఎဪڔᓤਭ߈༄༿ሌᓰ۸ੑጲሆᇕອă
•৔௥DŽऺಽ໌൛ႋ࡮ࢀDž
•ᅀීୢࡒ
•ା࡮
•๿ᇓີDŽᓤᎌ611nmၺਜ਼2ᒗ3ࢆ༹ஈଋDž
•ᒓக
ᓖፀ
ڳۡෞᄖሣڔᓤᏴ༄ࠊࡼดݾă༤ᇖڳᄖሣڔᓤᏴࠥࠀჅၤᆡᒙጲᅪࡼ໚჈
ྀੜ࢐ऱă
ڔᓤᒄ༄
ဧ፿Ⴒ૦ᄋ৙ࡼ༹ஈݚqaݟབྷޱࠊ࿟ࡼᎉฟĂ౱૞ા޺ă
ڔᓤᆡᒙ)5*
ڔᓤᅲ߅
ۡෞᄖሣڔᓤݛᒾ
ଶއۡෞᄖሣ5ࡼڔᓤᆡᒙ)6*
1
ڳۡෞᄖሣࡼ࢟Ꮞ߿࢛Ꭷޱࠊჿࠣሣࡼሆዘ࣪ᓰLj݀፿ᅀීୢ
୓໚೹ဟৼࢾ)6-1*ă
ሚᏴથݙถႆሆᄖሣ۳ݝࡼॖᒓă
ᅄᒦჅာᆐᔧݾᄖሣ஠ቲࠥݛઁࡼஉਫăጲሤᄴऱज೹ဟৼࢾ
ᎎݾᄖሣă
2 ဧ፿ᅀීୢࡒࢀܪ଑ۡෞᄖሣࡼᔧݾਜ਼ᎎݾ)6-2*ă
ގሆ༄ࠊೝݾࡼ༄ᑽᓏ࿟ࡼดኹᄟ)7*
ᅄᒦჅာᆐ୶ޱਜ਼TVWࢀ໱ޱࡼಿᔇLjᏴ༄ᑽᓏ࿟ᓤᎌڳ၄ă
ᓖፀ
•
༄ᑽᓏ࿟ࡼኹᄟဵဧ፿ଚᔇ૞൛ႋৼࢾࡵᆡࡼăގቘဟLj༿ᓖፀݙገႼડ
჈૞ཱུ჈ܤተă
• ิᔈ଄஠ቲڔᓤဟLjྙਫิ௻ࡻ༄ᑽᓏኹᄟ੪ซގሆLj༿ೊᇹளሾ࿜ኰཇ
ۑᓐă)༿ᓖፀิࡼளሾ࿜భถ્࣪ᑚࠨۑᓐ஠ቲ၃ॅă*
ڔᓤۡෞᄖሣ5)8*
ڔᓤᒄ༄
•
Ᏼఎဪጲሆݛᒾ༄༿ڳ༄ෂ೹ဟৼࢾࡵᆡࡼۡෞᄖሣގሆă
• ፿ݚঙᓕጥܭ๤ጲऴၺਜ਼༹ஈଋă
• Ᏼఎဪጲሆݛᒾ༄༿ੑੑ༹ᇸ༄ࠊLj߹བྷા޺Ăᎉᇁ૞ऴᇓଋă
1 ဧ፿๿ᇓີLj፿ࢅเࣞࡼ༹ஈଋྎጘڳ༄ࠊดݾ๿ဘăᔢੑࡼ
ྎጘဵ611nmၺଝ2Ă3ࢆ༹ஈଋDŽ8-1DžăDŽဧ፿࠙ၺ୓
ݙถ੪ੑ࢐஠ቲᆈࢯăDž
2 ႆሆۡෞᄖሣ۳ݝࡼॖᒓăဧ፿๿ᇓີLj፿ࢅเࣞࡼ༹ஈଋྎ
ጘ๿ဘഴ߲౶ࡼܭෂDŽ8-2Džă
•อᓕ۠ಭຢ݀ൻൻႆሆᅀීॖᒓă
•༿ᇖ࠭഍ጙݾDŽෂሶޱดࡼጙݾDžႆሆۣઐෞăิ୓Ᏼ)8-4*
ݛᒦႆሆࠥෞă
•༿ᇖཱུા޺૞ᒎᆬᐬࡵۡෞᄖሣࡼഴ߲ܭෂă
ڔᓤۡෞᄖሣဟ
•
ࠓᒇऱሶ࿟ᄰਭڳᄖሣࡼ࿟ዘਜ਼ჿࠣሣࡼሆዘ࣪ᓰ౶஠ቲࢾᆡăၺຳऱ
ሶ࿟ᄰਭڳܟዘᎧิ༄ෂᏴޱࠊ࿟ᔪࡼܪ଑DŽᅀීୢࢀDž࣪ᓰ஠ቲࢾ
ᆡă
• ิᏴ৔ᔫဟ༿ᇖཱུ༄ࠊܤছᐉăኊገဟ፿༹ஈଋྎጘᏳ๿ጙࠨă
• Ᏼ༄ࠊܤছᐉᒄ༄Ljิభጲઘࣅᄖሣጲࢯᑳ໚ᆡᒙă
• ࡩิڳᄖሣࢾᆡࡵิሯገࡼᆡᒙઁLjڳܪ଑߹བྷă
3 ڳۡෞᄖሣᐫࡵ༄ࠊ࿟)8-3*ă
4 ဧ፿Ⴒ૦ᄋ৙ࡼሴୢਦᒷ8ጲཀྵۣۡෞᄖሣಐৼ࢐ڔᓤࡵޱ
ࠊ࿟)8-4*ă
•ဧ፿ሴୢਦᒷဟ༿ږᓕᄖሣݙཱུ჈ጤࣅă
•࠭ᄖሣࡼᒦቦᆁᅪਦࣅă
•ዘᓹᄖሣࡼޠࣞਦࣅሴୢਦᒷLjኹ߲໮๵Ljጲ૝ࡻৎੑࡼම
ॖă
•༿ᇖਭॊ፿ೆ෠ݟᄖሣă
ᓖፀ
Ᏼଖኚሆෂࡼڔᓤݛᒾ༄༿ཀྵۣۡෞᄖሣጯᅲཝছᐉăᏴᄖሣᆚছᐉဟ
ଖኚሆབྷ્ဧᄖሣ࠭ޱࠊ࿟ᅙൢă
5 ဧ፿ᒓகڳࣶ᎜ࡼ༹ஈଋྎጘݟབྷLjཱུ݀ᄖሣߠॊছᐉă
ᆸඣ୐ፇ፿4.5ৈቃဟཱུᄖሣছᐉă
༿ᇖޞ၂ဧ፿ࠏज़૦૞໚჈ଝེ໭ଝႥছᐉࡼਭ߈ăᑚዹᔪ્
Ⴜડۡෞᄖሣă
t ᓞनෂ/ t
XAV-A1
* To the optional back camera or a video
equipment (to AUX 3).
+ ೌ୻ࡵభኡઁ࿳ሷ૦၁ຫ࿸۸)ೌ୻ࡵBVY4*